- 您現在的位置：買賣IC網 > PDF目錄24836 > 935285129112 (NXP SEMICONDUCTORS) LED DISPLAY DRIVER, PDSO28 PDF資料下載
參數資料
| 型號： | 935285129112 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 顯示驅動器 |
| 英文描述： | LED DISPLAY DRIVER, PDSO28 |
| 封裝： | 4.40 MM, PLASTIC, MO-153, SOT361-1, TSSOP-28 |
| 文件頁數： | 52/54頁 |
| 文件大小： | 410K |
| 代理商： | 935285129112 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁
PCA9685_2
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 02 — 16 July 2009
7 of 50
NXP Semiconductors
PCA9685
16-channel, 12-bit PWM Fm+ I2C-bus LED controller
PCA9564 (0000 000) or PCA9665 (1110 000) slave address which is active on
start-up
‘reserved for future use’ I2C-bus addresses (0000 011, 1111 1XX)
slave devices that use the 10-bit addressing scheme (1111 0XX)
slave devices that are designed to respond to the General Call address (0000 000)
which is used as the software reset address
High-speed mode (Hs-mode) master code (0000 1XX)
The last bit of the address byte denes the operation to be performed. When set to logic 1
a read is selected, while a logic 0 selects a write operation.
7.1.2 LED All Call I2C-bus address
Default power-up value (ALLCALLADR register): E0h or 1110 000X
Programmable through I2C-bus (volatile programming)
At power-up, LED All Call I2C-bus address is enabled. PCA9685 sends an ACK when
E0h (R/W = 0) or E1h (R/W = 1) is sent by the master.
See Section 7.3.7 “ALLCALLADR, LED All Call I2C-bus address” for more detail.
Remark: The default LED All Call I2C-bus address (E0h or 1110 000X) must not be used
as a regular I2C-bus slave address since this address is enabled at power-up. All the
PCA9685s on the I2C-bus will acknowledge the address if sent by the I2C-bus master.
7.1.3 LED Sub Call I2C-bus addresses
3 different I2C-bus addresses can be used
Default power-up values:
– SUBADR1 register: E2h or 1110 001X
– SUBADR2 register: E4h or 1110 010X
– SUBADR3 register: E8h or 1110 100X
Programmable through I2C-bus (volatile programming)
At power-up, Sub Call I2C-bus addresses are disabled. PCA9685 does not send an
ACK when E2h (R/W = 0) or E3h (R/W = 1), E4h (R/W = 0) or E5h (R/W = 1), or
E8h (R/W = 0) or E9h (R/W = 1) is sent by the master.
See Section 7.3.6 “SUBADR1 to SUBADR3, I2C-bus subaddress 1 to 3” for more detail.
Remark: The default LED Sub Call I2C-bus addresses may be used as regular I2C-bus
slave addresses as long as they are disabled.
Fig 4.
Slave address
R/W
002aad168
1
A5
A4
A3
A2
A1
A0
hardware selectable
slave address
fixed
相關PDF資料 |
PDF描述 |
|---|---|
| 935285129118 | LED DISPLAY DRIVER, PDSO28 |
| 935287058118 | LED DISPLAY DRIVER, PQCC28 |
| 935289802118 | LED DISPLAY DRIVER, PDSO28 |
| 935288883112 | DATACOM, INTERFACE CIRCUIT, PDSO8 |
| 935288883115 | DATACOM, INTERFACE CIRCUIT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 935286409157 | 制造商:NXP Semiconductors 功能描述:IC AMP AUDIO DGTL MONO D 24HVQFN |
| 935286496115 | 制造商:NXP Semiconductors 功能描述:IC ANALOG SWITCH SPDT 10XQFN |
| 935286689118 | 制造商:NXP Semiconductors 功能描述:935286689118 |
| 935286882115 | 制造商:NXP Semiconductors 功能描述:IC ANALOG SWITCH SPDT 10HVSON |
| 935286883115 | 制造商:NXP Semiconductors 功能描述:IC BUFFER/LINE DVR 3STATE 10XSON |
發布緊急采購，3分鐘左右您將得到回復。