Low Current Ultrasensitive Two-Wire
Chopper-Stabilized Unipolar Hall Effect Switches
A1147 and
A1148
9
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
Power Derating
The device must be operated below the maximum junction
temperature of the device, T
J(max)
. Under certain combinations of
peak conditions, reliable operation may require derating sup-
plied power or improving the heat dissipation properties of the
application. This section presents a procedure for correlating
factors affecting operating T
J
. (Thermal data is also available on
the Allegro MicroSystems Web site.)
The Package Thermal Resistance, R
qJA
, is a figure of merit sum-
marizing the ability of the application and the device to dissipate
heat from the junction (die), through all paths to the ambient air.
Its primary component is the Effective Thermal Conductivity,
K, of the printed circuit board, including adjacent devices and
traces. Radiation from the die through the device case, R
qJC
, is
relatively small component of R
qJA
. Ambient air temperature,
T
A
, and air motion are significant external factors, damped by
overmolding.
The effect of varying power levels (Power Dissipation, P
D
), can
be estimated. The following formulas represent the fundamental
relationships used to estimate T
J
, at P
D
.
P
D
= V
IN
?/DIV>
I
IN
(1)
   DT = P
D
?/DIV>
R
qJA
(2)
   T
J
= T
A
+ 擳     (3)
For example, given common conditions such as: T
A
= 25癈,
V
CC
= 12 V, I
CC
= 4 mA, and R
qJA
= 140 癈/W, then:
   P
D
= V
CC
?/DIV>
I
CC
= 12 V
?/DIV>
4 mA = 48 mW
  DT = P
D
?/DIV>
R
qJA
= 48 mW
?/DIV>
140 癈/W = 7癈
   T
J
= T
A
+ DT = 25癈 + 7癈 = 32癈
A worst-case estimate, P
D(max)
, represents the maximum allow-
able power level (V
CC(max)
, I
CC(max)
), without exceeding T
J(max)
,
at a selected R
qJA
and T
A
.
Example: Reliability for V
CC
at T
A
=
150癈, package UA, using
minimum-K PCB.
Observe the worst-case ratings for the device, specifically:
R
qJA
=
165癈/W, T
J(max)
=
165癈, V
CC(max)
=
24 V, and
I
CC(max)
=
17
mA.
Calculate the maximum allowable power level, P
D(max)
. First,
invert equation 3:
DT
max
= T
J(max)
T
A
= 165
癈
150
癈 = 15
癈
This provides the allowable increase to T
J
resulting from internal
power dissipation. Then, invert equation 2:
P
D(max)
= DT
max
?R
qJA
= 15癈 ?165 癈/W = 91 mW
Finally, invert equation 1 with respect to voltage:
V
CC(est)
= P
D(max)
? I
CC(max)
= 91 mW ?17 mA = 5 V
The result indicates that, at T
A
, the application and device can
dissipate adequate amounts of heat at voltages dV
CC(est)
.
Compare V
CC(est)
to V
CC(max)
. If V
CC(est)
d V
CC(max)
, then reli-
able operation between V
CC(est)
and V
CC(max)
requires enhanced
R
qJA
. If V
CC(est)
e V
CC(max)
, then operation between V
CC(est)
and
V
CC(max)
is reliable under these conditions.
相關代理商/技術參數 |
參數描述 |
A1148LUATI |
制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Low Current Ultrasensitive Two-Wire Chopper-Stabilized Unipolar Hall Effect Switches |
A1148LUATI-T |
制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Low Current Ultrasensitive Two-Wire Chopper-Stabilized Unipolar Hall Effect Switches |
A11490 |
功能描述:大功率LED - 單色 Amber 590nm 5 Watt
RoHS:否 制造商:Cree, Inc. 照明顏色:Blue 波長:465 nm 光強度: 光通量/輻射通量:500 mW 正向電流:350 mA 正向電壓:3.1 V 安裝風格:SMD/SMT 功率額定值: 系列:XB-D 封裝:Reel |
A114A |
制造商:General Electric Company 功能描述: 制造商:Advanced Semiconductor Inc 功能描述:Rectifier Diode, 100 Volt, Axial-B 制造商:SIGNAL DIODE 功能描述:Rectifier Diode, 100 Volt, Axial-B |
A11-4A |
制造商:Honeywell Sensing and Control 功能描述: |