- 您現在的位置：買賣IC網 > Datasheet目錄59 > A1148LUA-T (Allegro Microsystems Inc)IC SWITCH HALL EFFECT UNI 3-SIP Datasheet資料下載
參數資料
| 型號： | A1148LUA-T |
| 廠商： | Allegro Microsystems Inc |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 454K |
| 描述： | IC SWITCH HALL EFFECT UNI 3-SIP |
| 產品培訓模塊： | Current Sensor |
| 標準包裝： | 500 |
| 傳感范圍： | 80G 跳閘，10G 釋放 |
| 類型： | 單極開關 |
| 電源電壓： | 3.5 V ~ 24 V |
| 電流 - 電源： | 5mA |
| 輸出類型： | 數字，開路集電極 |
| 特點： | 穩壓電壓 |
| 工作溫度： | -40°C ~ 150°C |
| 封裝/外殼： | 3-SIP |
| 供應商設備封裝： | 3-SIP |
| 包裝： | 散裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁
Low Current Ultrasensitive Two-Wire
Chopper-Stabilized Unipolar Hall Effect Switches
A1147 and
A1148
7
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
Chopper Stabilization Technique
When using Hall-effect technology, a limiting factor for
switchpoint accuracy is the small signal voltage developed
across the Hall element. This voltage is disproportionally small
relative to the offset that can be produced at the output of the
Hall element. This makes it difficult to process the signal while
maintaining an accurate, reliable output over the specified oper-
ating temperature and voltage ranges.
Chopper stabilization is a unique approach used to minimize
Hall offset on the chip. The patented Allegro technique, namely
Dynamic Quadrature Offset Cancellation, removes key sources
of the output drift induced by thermal and mechanical stresses.
This offset reduction technique is based on a signal modulation-
demodulation process. The undesired offset signal is separated
from the magnetic field-induced signal in the frequency domain,
through modulation. The subsequent demodulation acts as a
modulation process for the offset, causing the magnetic field-
induced signal to recover its original spectrum at baseband, while
the DC offset becomes a high-frequency signal. The magnetic-
sourced signal then can pass through a low-pass filter, while
the modulated DC offset is suppressed. This configuration is
illustrated in figure 2.
The chopper stabilization technique uses a 200 kHz high
frequency clock. For demodulation process, a sample and hold
technique is used, where the sampling is performed at twice the
chopper frequency (400 kHz). This high-frequency operation
allows a greater sampling rate, which results in higher accuracy
and faster signal-processing capability. This approach desensi-
tizes the chip to the effects of thermal and mechanical stresses,
and produces devices that have extremely stable quiescent Hall
output voltages and precise recoverability after temperature
cycling. This technique is made possible through the use of a
BiCMOS process, which allows the use of low-offset, low-noise
amplifiers in combination with high-density logic integration
and sample-and-hold circuits.
The repeatability of magnetic field-induced switching is affected
slightly by a chopper technique. However, the Allegro high-
frequency chopping approach minimizes the affect of jitter and
makes it imperceptible in most applications. Applications that
are more likely to be sensitive to such degradation are those
requiring precise sensing of alternating magnetic fields; for
example, speed sensing of ring-magnet targets. For such applica-
tions, Allegro recommends its digital device families with lower
sensitivity to jitter. For more information on those devices,
contact your Allegro sales representative.
Figure 2. Chopper stabilization circuit (Dynamic Quadrature Offset Cancellation)
Amp
Regulator
Clock/Logic
Hall Element
Low-Pass
Filter
相關PDF資料 |
PDF描述 |
|---|---|
| A1155LUA-T | IC SW HALL EFFECT CHOPPER 3SIP |
| A1180LUA-T | IC SWITCH HALL EFFECT UNI 3-SIP |
| A1184LUA-T | IC SWITCH HALL EFFECT UNI 3-SIP |
| A1186LUA-T | IC SWITCH HALL EFFECT UNI 3-SIP |
| A1193LUA-T | IC SW HALL EFFECT CHOPPER 3SIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1148LUATI | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Low Current Ultrasensitive Two-Wire Chopper-Stabilized Unipolar Hall Effect Switches |
| A1148LUATI-T | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Low Current Ultrasensitive Two-Wire Chopper-Stabilized Unipolar Hall Effect Switches |
| A11490 | 功能描述:大功率LED - 單色 Amber 590nm 5 Watt RoHS:否 制造商:Cree, Inc. 照明顏色:Blue 波長:465 nm 光強度: 光通量/輻射通量:500 mW 正向電流:350 mA 正向電壓:3.1 V 安裝風格:SMD/SMT 功率額定值: 系列:XB-D 封裝:Reel |
| A114A | 制造商:General Electric Company 功能描述: 制造商:Advanced Semiconductor Inc 功能描述:Rectifier Diode, 100 Volt, Axial-B 制造商:SIGNAL DIODE 功能描述:Rectifier Diode, 100 Volt, Axial-B |
| A11-4A | 制造商:Honeywell Sensing and Control 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。