- 您現在的位置：買賣IC網 > PDF目錄164966 > A16L-JGM-T1-2 PUSHBUTTON SWITCH, DPDT, MOMENTARY, 3A, 30VDC, THROUGH HOLE-STRAIGHT PDF資料下載
參數資料
| 型號： | A16L-JGM-T1-2 |
| 元件分類： | 開關 |
| 英文描述： | PUSHBUTTON SWITCH, DPDT, MOMENTARY, 3A, 30VDC, THROUGH HOLE-STRAIGHT |
| 文件頁數： | 18/28頁 |
| 文件大小： | 3329K |
| 代理商： | A16L-JGM-T1-2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
A16
25
Rubber is used inside IP65 models. Do not allow the rubber to
become scratched or foreign matter to become attached to the
rubber.
Scratches and foreign matter will degrade the waterproofing, and
the Switch may fail operate correctly.
Screw-less Clamp Wiring Procedure
Connecting Wires
1. Strip the wires for 10 mm (allowable range: 10
± 1 mm).
2. If braided wire is used, twist the wire to straighten it out.
3. Insert the wire into the insertion hole while pressing the release
button at the side of the hole. (Using a precision screwdriver is
recommended.)
4. Let go of the release button to lock the wire into place.
5. After locking, pull on the wire gently to confirm that it is securely
locked.
Removing Wires
1. Remove wires by pulling them while pressing the release button.
Note: When reusing wires that have already been locked one, cut off the end of
the wire and strip the wire again before using.
Precautions
1. The mounting panel thickness must be 0.5 to 3.2 mm.
2. The mounting ring must be tightened to a torque 0.29 to 0.49 Nm.
3. The procedure for making the mounting hole for the screw-less
clamp connector is described on page 21. A mounting dimension
of at least 33 mm is required, however, because the Switch is
removed with the screw-less clamp connector mounted to the
panel. If Switches are mounted side-by-side separated by less
than the specified distance, it may not be possible to remove the
Switch.
4. Be sure to mount the Case to the Switch with the correct
orientation. Mount with the dimple on the Case facing in the same
direction as the side of the Switch with the direction arrow or the
word TOP.
5. Bend the end of the wire if braided wire is used with the screw-
less clamp connector.
6. When wiring, insert the wire until it comes into contact with
something. After wiring is completed, pull on the wires to confirm
that they are connected securely.
7. After wiring, ensure that continuous pressure is not applied to the
terminals.
8. Refer to internal connection diagrams and confirm the terminal
numbers before wiring.
Do not allow the Switch
to drop and hit the
ground.
Do not place or drop
heavy objects on the
Switch.
Do not operate the Switch
with hard or sharp objects.
Screwdriver
Hammer
Switch
Direction arrow
Case
dimple
Switch
TOP mark
Case
dimple
相關PDF資料 |
PDF描述 |
|---|---|
| A165L-ARM-12-1 | PUSHBUTTON SWITCH, SPDT, MOMENTARY, 3A, 30VDC, PANEL MOUNT |
| A165L-ARM-24-1 | PUSHBUTTON SWITCH, SPDT, MOMENTARY, 3A, 30VDC, PANEL MOUNT |
| A16L-TGM-24D-2S | PUSHBUTTON SWITCH, DPDT, MOMENTARY, 3A, 30VDC, PANEL MOUNT |
| A16L-TRA-5-2 | PUSHBUTTON SWITCH, DPDT, ALTERNATE, 3A, 30VDC, PANEL MOUNT |
| A16L-TRA-5D-2 | PUSHBUTTON SWITCH, DPDT, ALTERNATE, 3A, 30VDC, PANEL MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A16LJGN | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:CAP 16 SERIES RECTANGLR NEON GRN 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Access Push Button Switch Neon Lamp |
| A16L-JGN | 功能描述:開關配件 IL PB IP40 REC GRN NEON TYPE RoHS:否 制造商:C&K Components 類型:Cap 用于:Pushbutton Switches 設計目的: |
| A16LJGY | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:CAP 16 SERIES RECTANGULAR GREEN 制造商:Omron Electronic Components LLC 功能描述:Switch Access Push Button Switch LED 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Access Push Button Switch LED |
| A16L-JGY | 功能描述:開關配件 IL PB IP40 REC YEL NEON TYPE RoHS:否 制造商:C&K Components 類型:Cap 用于:Pushbutton Switches 設計目的: |
| A16LJPY | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:PURE YELLOW CAP FOR LED |
發布緊急采購，3分鐘左右您將得到回復。