- 您現(xiàn)在的位置：買賣IC網 > PDF目錄164966 > A16L-JGM-T1-2 PUSHBUTTON SWITCH, DPDT, MOMENTARY, 3A, 30VDC, THROUGH HOLE-STRAIGHT PDF資料下載
參數資料
| 型號： | A16L-JGM-T1-2 |
| 元件分類： | 開關 |
| 英文描述： | PUSHBUTTON SWITCH, DPDT, MOMENTARY, 3A, 30VDC, THROUGH HOLE-STRAIGHT |
| 文件頁數： | 19/28頁 |
| 文件大?。?/td> | 3329K |
| 代理商： | A16L-JGM-T1-2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
A16
26
Panel Mounting
After mounting the Pushbutton Unit (i.e., the Pushbutton and the
Case) to the panel, snap in the Switch Unit (i.e., the Switch and the
Lamp) from the back of the panel.
Mounting to the Panel
Insert the Pushbutton Unit into the front of the panel, and fix the lock
ring and mounting nut from the terminal side.
Make sure that the lock ring is aligned with the thread of the Case
and the edge of the lock ring is touching the panel.
Tighten the mounting nuts to a torque of 0.29 to 0.49 Nm.
Mounting the Switch Unit
Snap on the Switch Unit to the Pushbutton Unit.
Make sure that the Switch Unit has the correct orientation when
snapping it onto the Case. Align the dimple on the Case with the
groove between the case guards on the NC terminal side of the
Switch Unit in the way shown below, and push the Switch Unit into
the Case until it clicks into place. Confirm that the Switch Unit is
securely in place before using.
Removing the Switch Unit
Grip the part between the Switch holder of the Case and the Switch
Unit using the A16Z-5080 Extractor, and pull to remove the Switch
Unit.
Note: Refer to page 21 for PCB terminals.
Engraving
Engraving the Legend Plate
The characters must not be engraved deeper than 0.4 mm.
Apply an alcohol-based paint coating, such as melamine,
phthalate, or acrylic resin paint coating.
Mounting and Replacing the Pushbutton
Removing and Mounting the Pushbutton
(1) Remove the Pushbutton as shown in the following diagram. If the
Pushbutton cannot be removed by hand, use the A3PJ-5080
Extractor.
(2) When mounting the Operation Unit to the Case, press the entire
surface of the Operation Unit to surface A of the Case as shown
in the following diagram.
Case
Panel
Mounting nut
Lock ring
Edge
Thread
dimple
NC terminal
Groove between case guards
A16Z-5080 Extractor
Pushbutton
Case
Surface A
Operation Unit
相關PDF資料 |
PDF描述 |
|---|---|
| A165L-ARM-12-1 | PUSHBUTTON SWITCH, SPDT, MOMENTARY, 3A, 30VDC, PANEL MOUNT |
| A165L-ARM-24-1 | PUSHBUTTON SWITCH, SPDT, MOMENTARY, 3A, 30VDC, PANEL MOUNT |
| A16L-TGM-24D-2S | PUSHBUTTON SWITCH, DPDT, MOMENTARY, 3A, 30VDC, PANEL MOUNT |
| A16L-TRA-5-2 | PUSHBUTTON SWITCH, DPDT, ALTERNATE, 3A, 30VDC, PANEL MOUNT |
| A16L-TRA-5D-2 | PUSHBUTTON SWITCH, DPDT, ALTERNATE, 3A, 30VDC, PANEL MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A16LJGN | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:CAP 16 SERIES RECTANGLR NEON GRN 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Access Push Button Switch Neon Lamp |
| A16L-JGN | 功能描述:開關配件 IL PB IP40 REC GRN NEON TYPE RoHS:否 制造商:C&K Components 類型:Cap 用于:Pushbutton Switches 設計目的: |
| A16LJGY | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:CAP 16 SERIES RECTANGULAR GREEN 制造商:Omron Electronic Components LLC 功能描述:Switch Access Push Button Switch LED 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Access Push Button Switch LED |
| A16L-JGY | 功能描述:開關配件 IL PB IP40 REC YEL NEON TYPE RoHS:否 制造商:C&K Components 類型:Cap 用于:Pushbutton Switches 設計目的: |
| A16LJPY | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:PURE YELLOW CAP FOR LED |
發(fā)布緊急采購，3分鐘左右您將得到回復。