Revision 13 3-3 JTAG Pins Low power flash devices have a separate bank for the dedicated JTAG pins. The JTAG pins can" />
參數資料
型號: A3PE3000-1FGG484
廠商: Microsemi SoC
文件頁數: 162/162頁
文件大?。?/td> 0K
描述: IC FPGA 1KB FLASH 3M 484-FBGA
標準包裝: 40
系列: ProASIC3E
RAM 位總計: 516096
輸入/輸出數: 341
門數: 3000000
電源電壓: 1.425 V ~ 1.575 V
安裝類型: 表面貼裝
工作溫度: 0°C ~ 70°C
封裝/外殼: 484-BGA
供應商設備封裝: 484-FPBGA(23x23)
ProASIC3E Flash Family FPGAs
Revision 13
3-3
JTAG Pins
Low power flash devices have a separate bank for the dedicated JTAG pins. The JTAG pins can be run
at any voltage from 1.5 V to 3.3 V (nominal). VCC must also be powered for the JTAG state machine to
operate, even if the device is in bypass mode; VJTAG alone is insufficient. Both VJTAG and VCC to the
part must be supplied to allow JTAG signals to transition the device. Isolating the JTAG power supply in a
separate I/O bank gives greater flexibility in supply selection and simplifies power supply and PCB
design. If the JTAG interface is neither used nor planned for use, the VJTAG pin together with the TRST
pin could be tied to GND.
TCK
Test Clock
Test clock input for JTAG boundary scan, ISP, and UJTAG. The TCK pin does not have an internal pull-
up/-down resistor. If JTAG is not used, Microsemi recommends tying off TCK to GND through a resistor
placed close to the FPGA pin. This prevents JTAG operation in case TMS enters an undesired state.
Note that to operate at all VJTAG voltages, 500 W to 1 k
will satisfy the requirements. Refer to
Table 3-1 for more information.
TDI
Test Data Input
Serial input for JTAG boundary scan, ISP, and UJTAG usage. There is an internal weak pull-up resistor
on the TDI pin.
TDO
Test Data Output
Serial output for JTAG boundary scan, ISP, and UJTAG usage.
TMS
Test Mode Select
The TMS pin controls the use of the IEEE 1532 boundary scan pins (TCK, TDI, TDO, TRST). There is an
internal weak pull-up resistor on the TMS pin.
TRST
Boundary Scan Reset Pin
The TRST pin functions as an active-low input to asynchronously initialize (or reset) the boundary scan
circuitry. There is an internal weak pull-up resistor on the TRST pin. If JTAG is not used, an external pull-
down resistor could be included to ensure the test access port (TAP) is held in reset mode. The resistor
values must be chosen from Table 3-1 and must satisfy the parallel resistance value requirement. The
values in Table 3-1 correspond to the resistor recommended when a single device is used, and the
equivalent parallel resistor when multiple devices are connected via a JTAG chain.
In critical applications, an upset in the JTAG circuit could allow entrance to an undesired JTAG state. In
such cases, Microsemi recommends tying off TRST to GND through a resistor placed close to the FPGA
pin.
Note that to operate at all VJTAG voltages, 500
to 1 k will satisfy the requirements.
Table 3-1 Recommended Tie-Off Values for the TCK and TRST Pins
VJTAG
Tie-Off Resistance
VJTAG at 3.3 V
200
to 1 k
VJTAG at 2.5 V
200
to 1 k
VJTAG at 1.8 V
500
to 1 k
VJTAG at 1.5 V
500
to 1 k
Notes:
1. Equivalent parallel resistance if more than one device is on the JTAG chain
2. The TCK pin can be pulled up/down.
3. The TRST pin is pulled down.
相關PDF資料
PDF描述
M1A3PE3000-1FGG484 IC FPGA 1KB FLASH 3M 484-FBGA
AFS600-1FGG256K IC FPGA 4MB FLASH 600K 256FBGA
AFS600-1FG256K IC FPGA 4MB FLASH 600K 256FBGA
M1A3PE3000-FG896 IC FPGA 1KB FLASH 3M 896-FBGA
M1A3PE3000-FGG896 IC FPGA 1KB FLASH 3M 896-FBGA
相關代理商/技術參數
參數描述
A3PE3000-1FGG484I 功能描述:IC FPGA 1KB FLASH 3M 484-FBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:ProASIC3E 標準包裝:1 系列:ProASICPLUS LAB/CLB數:- 邏輯元件/單元數:- RAM 位總計:129024 輸入/輸出數:248 門數:600000 電源電壓:2.3 V ~ 2.7 V 安裝類型:表面貼裝 工作溫度:- 封裝/外殼:352-BFCQFP,帶拉桿 供應商設備封裝:352-CQFP(75x75)
A3PE3000-1FGG896 功能描述:IC FPGA 1KB FLASH 3M 896-FBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:ProASIC3E 產品培訓模塊:Three Reasons to Use FPGA's in Industrial Designs Cyclone IV FPGA Family Overview 特色產品:Cyclone? IV FPGAs 標準包裝:60 系列:CYCLONE® IV GX LAB/CLB數:9360 邏輯元件/單元數:149760 RAM 位總計:6635520 輸入/輸出數:270 門數:- 電源電壓:1.16 V ~ 1.24 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:484-BGA 供應商設備封裝:484-FBGA(23x23)
A3PE3000-1FGG896ES 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:ProASIC3E Flash Family FPGAs
A3PE3000-1FGG896I 功能描述:IC FPGA 1KB FLASH 3M 896-FBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:ProASIC3E 標準包裝:1 系列:ProASICPLUS LAB/CLB數:- 邏輯元件/單元數:- RAM 位總計:129024 輸入/輸出數:248 門數:600000 電源電壓:2.3 V ~ 2.7 V 安裝類型:表面貼裝 工作溫度:- 封裝/外殼:352-BFCQFP,帶拉桿 供應商設備封裝:352-CQFP(75x75)
A3PE3000-1FGG896PP 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:ProASIC3E Flash Family FPGAs