- 您現在的位置：買賣IC網 > PDF目錄298744 > A42MX24-3VQ100A (Electronic Theatre Controls, Inc.) 40MX and 42MX FPGA Families PDF資料下載
參數資料
| 型號： | A42MX24-3VQ100A |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 40MX and 42MX FPGA Families |
| 中文描述： | 40MX和42MX FPGA系列 |
| 文件頁數： | 59/93頁 |
| 文件大?。?/td> | 854K |
| 代理商： | A42MX24-3VQ100A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁當前第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁
62
Data Device Corporation
www.ddc-web.com
BU-6474X/6484X/6486X
J-07/05-0
SELECT (I)
B12
Device Select.
Generally connected to a CPU address decoder output to select the Mark3 for a
transfer to/from either RAM or register.
TABLE 62. PROCESSOR INTERFACE CONTROL
SIGNAL NAME
DESCRIPTION
BU-64840B3
BU-64860B3
BALL
B12
STRBD (I)
A12
Strobe Data.
Used in conjunction with SELECT to initiate and control the data transfer cycle
between the host processor and the Mark3. STRBD must be asserted low through
the full duration of the transfer cycle.
A12
ADDR_LAT(I) /
MEMOE (O)
L9
Memory Output Enable or Address Latch.
In buffered mode, the ADDR_LAT input is used to configure the buffers for A15-
A0, SELECT, MEM/REG, and MSB/LSB (for 8-bit mode only) in latched mode
(when low) or transparent mode (when high). That is, the Mark3's internal trans-
parent latches will track the values on A15-A0, SELECT, MEM/REG, and
MSB/LSB when ADDR_LAT is high, and latch the values when ADDR_LAT goes
low.
In general, for interfacing to processors with a non-multiplexed address/data bus,
ADDR_LAT should be hardwired to logic "1". For interfacing to processors with a
multiplexed address/data bus, ADDR_LAT should be connected to a signal that
indicates a valid address when ADDR_LAT is logic "1".
In transparent mode, MEMOE output signal is used to enable data outputs for
external RAM read cycles (normally connected to the OE input signal on external
RAM chips).
U10
ZEROWAIT (I) /
MEMWR (O)
M10
Memory Write or Zero Wait.
In buffered mode, input signal (ZEROWAIT) used to select between the zero wait
mode (ZEROWAIT = "0") and the non-zero wait mode (ZEROWAIT = "1").
In transparent mode, active low output signal (MEMWR) asserted low during
memory write transfers to strobe data into external RAM (normally connected to
the WR input signal on external RAM chips).
T8
16 / 8 (I) /
DTREQ (O)
L10
Data Transfer Request or Data Bus Select.
In buffered mode, input signal 16/8 used to select between the 16 bit data transfer
mode (16/8 = "1") and the 8-bit data transfer mode (16/8 = "0").
In transparent mode (16-bit only), active low level output signal DTREQ used to
request access to the processor/RAM interface bus (address and data buses).
R17
MSB / LSB (I) /
DTGRT (I)
J7
Data Transfer Grant or Most Significant Byte/Least Significant Byte.
In 8-bit buffered mode, input signal (MSB/LSB) used to indicate which byte is cur-
rently being transferred (MSB or LSB). The logic sense of MSB/LSB is controlled
by the POL_SEL input. MSB/LSB is not used in the 16-bit buffered mode.
In transparent mode, active low input signal (DTGRT) asserted in response to the
DTREQ output to indicate that control of the external processor/RAM bus has
been transferred from the host processor to the Mark3.
B6
RD / WR (I)
A11
Read/Write.
For host processor access, RD/WR selects between reading and writing. In the
16-bit buffered mode, if POL_SEL is logic "0”, then RD/WR should be low (logic
"0") for read accesses and high (logic "1") for write accesses. If POL_SEL is logic
"1", or the interface is configured for a mode other than 16-bit buffered mode, then
RD/WR is high (logic "1") for read accesses and low (logic "0") for write accesses.
B11
BU-64743B8
BU-64843B8
BU-64863B8
BALL
BALL GRID ARRAY PACKAGE - SIGNAL DESCRIPTIONS BY FUNCTIONAL GROUPS (CONT.)
相關PDF資料 |
PDF描述 |
|---|---|
| A42MX24-3VQ100B | 40MX and 42MX FPGA Families |
| A42MX36-2PQ100B | 40MX and 42MX FPGA Families |
| A42MX36-2PQ100ES | 40MX and 42MX FPGA Families |
| A42MX36-2TQ100 | 40MX and 42MX FPGA Families |
| A42MX36-2TQ100A | 40MX and 42MX FPGA Families |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A42MX24-FPL84 | 功能描述:IC FPGA MX SGL CHIP 36K 84-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:MX 標準包裝:40 系列:SX-A LAB/CLB數:6036 邏輯元件/單元數:- RAM 位總計:- 輸入/輸出數:360 門數:108000 電源電壓:2.25 V ~ 5.25 V 安裝類型:表面貼裝 工作溫度:0°C ~ 70°C 封裝/外殼:484-BGA 供應商設備封裝:484-FPBGA（27X27） |
| A42MX24-FPLG84 | 功能描述:IC FPGA MX SGL CHIP 36K 84-PLCC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:MX 標準包裝:40 系列:SX-A LAB/CLB數:6036 邏輯元件/單元數:- RAM 位總計:- 輸入/輸出數:360 門數:108000 電源電壓:2.25 V ~ 5.25 V 安裝類型:表面貼裝 工作溫度:0°C ~ 70°C 封裝/外殼:484-BGA 供應商設備封裝:484-FPBGA（27X27） |
| A42MX24-FPQ160 | 功能描述:IC FPGA MX SGL CHIP 36K 160-PQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:MX 標準包裝:40 系列:SX-A LAB/CLB數:6036 邏輯元件/單元數:- RAM 位總計:- 輸入/輸出數:360 門數:108000 電源電壓:2.25 V ~ 5.25 V 安裝類型:表面貼裝 工作溫度:0°C ~ 70°C 封裝/外殼:484-BGA 供應商設備封裝:484-FPBGA（27X27） |
| A42MX24-FPQ208 | 功能描述:IC FPGA MX SGL CHIP 36K 160-PQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:MX 標準包裝:40 系列:SX-A LAB/CLB數:6036 邏輯元件/單元數:- RAM 位總計:- 輸入/輸出數:360 門數:108000 電源電壓:2.25 V ~ 5.25 V 安裝類型:表面貼裝 工作溫度:0°C ~ 70°C 封裝/外殼:484-BGA 供應商設備封裝:484-FPBGA（27X27） |
| A42MX24-FPQG160 | 功能描述:IC FPGA MX SGL CHIP 36K 160-PQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:MX 標準包裝:40 系列:SX-A LAB/CLB數:6036 邏輯元件/單元數:- RAM 位總計:- 輸入/輸出數:360 門數:108000 電源電壓:2.25 V ~ 5.25 V 安裝類型:表面貼裝 工作溫度:0°C ~ 70°C 封裝/外殼:484-BGA 供應商設備封裝:484-FPBGA（27X27） |
發布緊急采購，3分鐘左右您將得到回復。