- 您現在的位置：買賣IC網 > PDF目錄9290 > AD5204BRZ100 (Analog Devices Inc)IC DGTL POT QUAD 100K 24-SOIC PDF資料下載
參數資料
| 型號： | AD5204BRZ100 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 5/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DGTL POT QUAD 100K 24-SOIC |
| 標準包裝： | 31 |
| 接片： | 256 |
| 電阻（歐姆）： | 100k |
| 電路數： | 4 |
| 溫度系數： | 標準值 700 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | 4 線 SPI（芯片選擇） |
| 電源電壓： | 2.7 V ~ 5.5 V，±2.3 V ~ 2.7 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 24-SOIC W |
| 包裝： | 管件 |
AD5204/AD5206
Rev. C | Page 13 of 20
PROGRAMMING THE VARIABLE RESISTOR
RHEOSTAT OPERATION
The nominal resistance of the RDAC between Terminal A and
Terminal B is available with values of 10 kΩ, 50 kΩ, and 100 kΩ.
The last digits of the part number determine the nominal
resistance value; for example, 10 kΩ = 10 and 100 kΩ = 100.
The nominal resistance (RAB) of the VR has 256 contact points
accessed by the wiper terminal, plus Terminal B contact. The
8-bit data-word in the RDAC latch is decoded to select one of
the 256 possible settings. The first connection of the wiper starts
at Terminal B for the 0x00 data. This Terminal B connection has a
wiper contact resistance of 45 Ω. The second connection (for a
10 kΩ part) is the first tap point, located at 84 Ω [= RAB (nominal
resistance)/256 + RW = 84 Ω + 45 Ω] for the 0x01 data. The
third connection is the next tap point, representing 78 + 45 =
123 Ω for the 0x02 data. Each LSB data value increase moves
the wiper up the resistor ladder until the last tap point is
reached at 10,006 Ω. The wiper does not directly connect to
Terminal A. See Figure 21 for a simplified diagram of the
equivalent RDAC circuit.
The general transfer equation determining the digitally
programmed output resistance between the Wx and Bx
terminals is
RWB (Dx) = (Dx)/256 × RAB + RW
(1)
where Dx is the data contained in the 8-bit RDACx latch, and
RAB is the nominal end-to-end resistance.
For example, when VB = 0 V and Terminal A is open circuited, the
output resistance values are set as outlined in Table 7 for the
RDAC latch codes (applies to the 10 kΩ potentiometer).
Table 7. Output Resistance Values for the RDAC Latch Codes—
VB = 0 V and Terminal A = Open Circuited
D (Dec)
RWB (Ω)
Output State
255
10006
Full scale
128
5045
Midscale (PR = 0 condition)
1
84
1 LSB
0
45
Zero scale (wiper contact resistance)
In the zero-scale condition, a finite total wiper resistance of 45 Ω
is present. Regardless of which setting the part is operating in,
care should be taken to limit the current between Terminal A to
Terminal B, Wiper W to Terminal A, and Wiper W to Terminal
B, to the maximum continuous current of ±5.65 mA(10 kΩ) or
±1.35 mA(50 kΩ and 100 kΩ) or pulse current of ±20 mA.
Otherwise, degradation or possible destruction of the internal
switch contact, can occur.
Like the mechanical potentiometer that the RDAC replaces,
the RDAC is completely symmetrical. The resistance between
Wiper W and Terminal A produces a digitally controlled
resistance, RWA. When these terminals are used, Terminal B
should be tied to the wiper. Setting the resistance value for RWA
starts at a maximum value of resistance and decreases as the
data loaded to the latch is increased in value. The general
transfer equation for this operation is
RWA (Dx) = (256 Dx)/256 × RAB + RW
(2)
where Dx is the data contained in the 8-bit RDACx latch, and
RAB is the nominal end-to-end resistance.
For example, when VA = 0 V and Terminal B is tied to Wiper W,
the output resistance values outlined in Table 8 are set for the
RDAC latch codes.
Table 8. Output Resistance Values for the RDAC Latch Codes—
VA = 0 V and Terminal B Tied to Wiper W
D (DEC)
RWA (Ω)
Output State
255
84
Full scale
128
5045
Midscale (PR = 0 condition)
1
10006
1 LSB
0
10045
Zero scale
The typical distribution of RAB from channel to channel matches
to within ±1%. However, device-to-device matching is process
lot dependent, having a ±30% variation. The change in RAB in
terms of temperature has a 700 ppm/°C temperature coefficient.
相關PDF資料 |
PDF描述 |
|---|---|
| MS3450L24-28PZ | CONN RCPT 24POS WALL MNT W/PINS |
| DS1100U-45+ | IC DELAY LINE 5TAP 45NS 8-USOP |
| VI-2ND-MY-F3 | CONVERTER MOD DC/DC 85V 50W |
| AD5206BRU50-REEL | IC DGTL POT 6CH 256POS 24-TSSOP |
| VI-2NF-MY-F4 | CONVERTER MOD DC/DC 72V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5204BRZ100-REEL | 功能描述:IC DGTL POT QUAD 100K 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| AD5204BRZ10-REEL | 功能描述:IC DGTL POT QUAD 10K 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| AD5204BRZ50 | 功能描述:IC DGTL POT QUAD 50K 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| AD5204BRZ-50 | 制造商:Analog Devices 功能描述:DIGITAL POT QUAD 50K 5204 SOIC24 |
| AD5204BRZ50-REEL | 功能描述:IC DGTL POT QUAD 50K 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。