- 您現在的位置：買賣IC網 > PDF目錄6021 > AD524CDZ (Analog Devices Inc)IC AMP INST 1MHZ PREC LN 16CDIP PDF資料下載
參數資料
| 型號： | AD524CDZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP INST 1MHZ PREC LN 16CDIP |
| 標準包裝： | 1 |
| 放大器類型： | 儀表 |
| 電路數： | 1 |
| 轉換速率： | 5 V/µs |
| 增益帶寬積： | 1MHz |
| -3db帶寬： | 1MHz |
| 電流 - 輸入偏壓： | 15nA |
| 電壓 - 輸入偏移： | 50µV |
| 電流 - 電源： | 3.5mA |
| 電壓 - 電源，單路/雙路(±)： | ±6 V ~ 18 V |
| 工作溫度： | -25°C ~ 85°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 16-CDIP（0.300"，7.62mm） |
| 供應商設備封裝： | 16-CDIP 側面銅焊 |
| 包裝： | 管件 |
| 產品目錄頁面： | 770 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD524
Rev. F | Page 15 of 28
THEORY OF OPERATION
The AD524 is a monolithic instrumentation amplifier based
on the classic 3-op amp circuit. The advantage of monolithic
construction is the closely matched components that enhance
the performance of the input preamplifier. The preamplifier
section develops the programmed gain by the use of feedback
concepts. The programmed gain is developed by varying the
value of RG (smaller values increase the gain) while the feedback
forces the collector currents (Q1, Q2, Q3, and Q4) to be constant,
which impresses the input voltage across RG.
As RG is reduced to increase the programmed gain, the
transconductance of the input preamplifier increases to the
transconductance of the input transistors. This has three
important advantages. First, this approach allows the circuit
to achieve a very high open-loop gain of 3 × 108 at a programmed
gain of 1000, thus reducing gain-related errors to a negligible
30 ppm. Second, the gain bandwidth product, which is deter-
mined by C3 or C4 and the input transconductance, reaches
25 MHz. Third, the input voltage noise reduces to a value
determined by the collector current of the input transistors
for an RTI noise of 7 nV/√Hz at G = 1000.
INPUT PROTECTION
As interface amplifiers for data acquisition systems, instru-
mentation amplifiers are often subjected to input overloads,
that is, voltage levels in excess of the full scale for the selected
gain range. At low gains (10 or less), the gain resistor acts as a
current limiting element in series with the inputs. At high gains,
the lower value of RG does not adequately protect the inputs
from excessive currents. Standard practice is to place series
limiting resistors in each input, but to limit input current to
below 5 mA with a full differential overload (36 V) requires
over 7kΩ of resistance, which adds 10 nV√Hz of noise. To
provide both input protection and low noise, a special series
protection FET is used.
A unique FET design was used to provide a bidirectional
current limit, thereby protecting against both positive and
negative overloads. Under nonoverload conditions, three
channels (CH2, CH3, CH4) act as a resistance (≈1 kΩ) in series
with the input as before. During an overload in the positive
direction, a fourth channel, CH1, acts as a small resistance
(≈3 kΩ) in series with the gate, which draws only the leakage
current, and the FET limits IDSS. When the FET enhances under
a negative overload, the gate current must go through the small
FET formed by CH1 and when this FET goes into saturation,
the gate current is limited and the main FET goes into controlled
enhancement. The bidirectional limiting holds the maximum
input current to 3 mA over the 36 V range.
INPUT OFFSET AND OUTPUT OFFSET
Voltage offset specifications are often considered a figure of
merit for instrumentation amplifiers. While initial offset may
be adjusted to zero, shifts in offset voltage due to temperature
variations causes errors. Intelligent systems can often correct
this factor with an autozero cycle, but there are many small-
signal high-gain applications that do not have this capability.
+Vs
RG2
AD712
1/2
9.09k
1k
100
16.2k
1/2
16.2k
1.62M
1.82k
10
100
1000
G = 1, 10, 100
G = 1000
AD524
+VS
–
+
–VS
1
16
13
12
9
11
10
6
3
8
7
2
1F
–VS
1F
3
2
8
1
5
6
4
7
0
05
00-
033
+
–
+
–
Figure 33. Noise Test Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| RMCF0603JT150R | RES 150 OHM 1/10W 5% 0603 SMD |
| RMCF0603JT2M20 | RES 2.2M OHM 1/10W 5% 0603 SMD |
| RMCF0603JT330K | RES 330K OHM 1/10W 5% 0603 SMD |
| UESD5.0DT5G | DIODE ESD PROTECT 5V SOT-723 |
| RMCF0603JT82K0 | RES 82K OHM 1/10W 5% 0603 SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD524CE | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述: |
| AD524S | 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Instrumentation Amplifier |
| AD524SCHIPS | 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Instrumentation Amplifier |
| AD524SD | 功能描述:IC AMP INST 1MHZ PREC LN 16CDIP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.028 V/µs 增益帶寬積:105kHz -3db帶寬:- 電流 - 輸入偏壓:3nA 電壓 - 輸入偏移:100µV 電流 - 電源:3.3µA 電流 - 輸出 / 通道:12mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:剪切帶 (CT) 其它名稱:OP481GRUZ-REELCT |
| AD524SD/883B | 功能描述:儀表放大器 PRECISION LOW NOISE IN AM RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
發布緊急采購，3分鐘左右您將得到回復。