- 您現在的位置：買賣IC網 > PDF目錄16611 > AD5258EVAL (Analog Devices Inc)BOARD EVAL FOR AD5258 DGTL POT PDF資料下載
參數資料
| 型號： | AD5258EVAL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR AD5258 DGTL POT |
| 標準包裝： | 1 |
| 主要目的： | 數字電位器 |
| 已用 IC / 零件： | AD5258 |
| 已供物品： | 板 |
| 相關產品： | AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOP AD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOP AD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOP AD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOP AD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOP AD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOP AD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOP AD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
Data Sheet
AD5258
Rev. D | Page 15 of 24
I2C INTERFACE
Note that the wiper’s default value prior to programming the
EEPROM is midscale.
The master initiates a data transfer by establishing a start con-
dition when a high-to-low transition on the SDA line occurs
while SCL is high (see Figure 3). The next byte is the slave
address byte, which consists of the slave address (first seven bits)
followed by an R/W bit (see Table 6). When the R/W bit is high,
the master reads from the slave device. When the R/W bit is
low, the master writes to the slave device.
The slave address of the part is determined by two configurable
address pins, AD0 and AD1. The state of these two pins is regis-
tered upon power-up and decoded into a corresponding I2C
7-bit address (see Table 5). The slave address corresponding to
the transmitted address bits responds by pulling the SDA line
low during the ninth clock pulse (this is termed the slave
acknowledge bit).
At this stage, all other devices on the bus remain idle while the
selected device waits for data to be written to or read from its
serial register.
WRITING
In the write mode, the last bit (R/W) of the slave address byte is
logic low. The second byte is the instruction byte. The first three
bits of the instruction byte are the command bits (see Table 6).
The user must choose whether to write to the RDAC register or
EEPROM register or to activate the software write protect (see
Table 7 to Table 10). The final five bits are all zeros (see Table 13
and Table 14). The slave again responds by pulling the SDA line
low during the ninth clock pulse.
The final byte is the data byte MSB first. Don’t cares can be
left either high or low. In the case of the write protect mode,
data is not stored; rather, a logic high in the LSB enables write
protect. Likewise, a logic low disables write protect. The slave
again responds by pulling the SDA line low during the ninth
clock pulse.
STORING/RESTORING
In this mode, only the address and instruction bytes are nec-
essary. The last bit (R/W) of the address byte is logic low. The
first three bits of the instruction byte are the command bits
(see Table 6). The two choices are transfer data from RDAC-
to-EEPROM (store) or from EEPROM-to-RDAC (restore).
The final five bits are all zeros (see Table 13 and Table 14). In
addition, users should issue an NOP command immediately
after restoring the EEMEM setting to RDAC, thereby mini-
mizing supply current dissipation.
READING
Assuming the register of interest was not just written to, it is
necessary to write a dummy address and instruction byte. The
instruction byte will vary depending on whether the data that
is wanted is the RDAC register, EEPROM register, or tolerance
register (see Table 11 to Table 16).
After the dummy address and instruction bytes are sent, a repeat
start is necessary. After the repeat start, another address byte is
needed, except this time the R/W bit is logic high. Following
this address byte is the readback byte containing the informa-
tion requested in the instruction byte. Read bits appear on the
negative edges of the clock. Don’t cares may be in either a high
or low state.
The tolerance register can be read back individually (see
Modes section for detailed information on the interpretation
of the tolerance bytes.
After all data bits have been read or written, a stop condition is
established by the master. A stop condition is defined as a low-
to-high transition on the SDA line while SCL is high. In write
mode, the master pulls the SDA line high during the 10th clock
pulse to establish a stop condition (see Table 8). In read mode,
the master issues a no acknowledge for the ninth clock pulse
(that is, the SDA line remains high). The master then brings the
SDA line low before the 10th clock pulse and raises SDA high to
establish a stop condition (see Table 11).
A repeated write function provides the user with the flexibility
of updating the RDAC output multiple times after addressing
and instructing the part only once. For example, after the RDAC
has acknowledged its slave address and instruction bytes in the
write mode, the RDAC output is updated on each successive
byte until a stop condition is received. If different instructions
are needed, the write/read mode must restart with a new slave
address, instruction, and data byte. Similarly, a repeated read
function of the RDAC is also allowed.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B33-EW | CONVERTER MOD DC/DC 24V 100W |
| V110C5T75BL | CONVERTER MOD DC/DC 5V 75W |
| EMC07DRTS-S13 | CONN EDGECARD 14POS .100 EXTEND |
| IMCSN-0400-25-U | HEAT SHRINK IMCSN 0400 BK 25FT |
| H3BKH-4006M | IDC CABLE - HSR40H/AE40M/HPK40H |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5258EVAL2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Nonvolatile, I2C-Compatible 64-Position, Digital Potentiometer |
| AD5259 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Nonvolatile, I2C-Compatible 256-Position, Digital Potentiometer |
| AD5259BCPZ100-R7 | 功能描述:IC POT DGTL 100K 256POS 10LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,300 系列:WiperLock™ 接片:257 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 150 ppm/°C 存儲器類型:易失 接口:3 線 SPI（芯片選擇） 電源電壓:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-VDFN 裸露焊盤 供應商設備封裝:8-DFN-EP（3x3） 包裝:帶卷 (TR) |
| AD5259BCPZ10-R7 | 功能描述:IC POT DGTL 10K 256POS 10LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| AD5259BCPZ50-R7 | 功能描述:IC POT DGTL 50K 256POS 10LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。