- 您現在的位置：買賣IC網 > PDF目錄9291 > AD5290YRMZ50-R7 (Analog Devices Inc)IC POT DGTL 50KW 256POS 10-MSOP PDF資料下載
參數資料
| 型號： | AD5290YRMZ50-R7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DGTL 50KW 256POS 10-MSOP |
| 標準包裝： | 1,000 |
| 接片： | 256 |
| 電阻（歐姆）： | 50k |
| 電路數： | 1 |
| 溫度系數： | 標準值 35 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | 4 線 SPI（芯片選擇） |
| 電源電壓： | 4.5 V ~ 30 V，±4.5 V ~ 15 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
| 配用： | EVAL-AD5290EBZ-ND - BOARD EVAL FOR AD5290 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
Data Sheet
AD5290
Rev. C | Page 15 of 20
THEORY OF OPERATION
PROGRAMMING THE VARIABLE RESISTOR
Rheostat Operation
The part operates in the rheostat mode when only two termi-
nals are used as a variable resistor. The unused terminal can
be floating or tied to the W terminal as shown in Figure 26.
A
W
B
A
W
B
A
W
B
04716-011
Figure 26. Rheostat Mode Configuration
The nominal resistance between Terminal A and Terminal B,
RAB, is available in 10 k, 50 k, and 100 k with ±30% toler-
ance and has 256 tap points accessed by the wiper terminal. The
8-bit data in the RDAC latch is decoded to select one of the 256
possible settings. Figure 27 shows a simplified RDAC structure.
4RS
2RS
RS
RW
W
RS
2RS
4RS
A
RW
B
8-BIT ADDRESS
DECODER
04716-012
Figure 27. AD5290 Simplified RDAC Circuit.
(RS = Step Resistor, RW = Wiper Resistor)
In order to achieve optimum cost performance, Analog Devices
has patented the RDAC segmentation architecture for all the
digital potentiometers. In particular, the AD5290 employs a
3-stage segmentation approach as shown in Figure 27. As
a result, the general equation determining the digitally
programmed output resistance between the W terminal
and B terminal is
W
AB
WB
R
D
R
×
+
×
=
3
256
)
(
(1)
where:
D is the decimal equivalent of the binary code loaded in
the 8-bit RDAC register from 0 to 255.
RAB is the end-to-end resistance.
RW is one of the wiper resistances contributed by the on
resistance of an internal switch.
The AD5290 wiper switch is designed with the transmission
gate CMOS topology and with the gate voltage derived from
VDD. The wiper resistance, RW, is a function of VDD and
temperature. Contrary to the temperature coefficient of the RAB,
which is only 35 ppm/°C, the temperature coefficient of the wiper
resistance is significantly higher because the wiper resistance
doubles from 25°C to 125°C. As a result, the user must take into
consideration the contribution of RW on the desirable
resistance. On the other hand, the wiper resistance is insensitive
to the tap point potential. As a result, RW remains relatively flat
at a given VDD and temperature at various codes.
Assuming that an ideal 10 k part is used, the wiper’s first
connection starts at the B terminal for the programming code
of 0x00 where SWB is closed. The minimum resistance between
Terminal W and Terminal B is, therefore, generally 150 . The
second connection is the first tap point, which corresponds to
189 (RWB = 1/256 × RAB + 3RW = 39 + 150 ) for code 0x01,
and so on. Each LSB data value increase moves the wiper up the
resistor ladder until the last tap point is reached at 10,110 .
In the zero-scale condition, a finite total wiper resistance of
150 is present. Regardless of which setting the part is oper-
ating in, care should be taken to limit the current between
the A terminal to B terminal, W terminal to A terminal, and
W terminal to B terminal, to the maximum dc current of 5 mA
or pulse current of 20 mA. Otherwise, degradation, or possible
destruction of the internal switch contact, can occur.
Similar to the mechanical potentiometer, the resistance of
the RDAC between the W terminal and the A terminal also
produces a digitally controlled complementary resistance, RWA.
RWA starts at the maximum resistance value and decreases as
the data loaded into the latch increases. The general equation
for this operation is
W
AB
WA
R
D
R
×
+
×
=
3
256
)
(
(2)
相關PDF資料 |
PDF描述 |
|---|---|
| VE-2TN-MX-B1 | CONVERTER MOD DC/DC 18.5V 75W |
| M83723/77W16247 | CONN PLUG 24POS STRAIGHT W/SCKT |
| VE-2T2-MX-B1 | CONVERTER MOD DC/DC 15V 75W |
| M83723/77R16246 | CONN PLUG 24POS STRAIGHT W/SCKT |
| VI-B60-IU-F3 | CONVERTER MOD DC/DC 5V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5290YRMZ50-RL7 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Compact +30V/【15V 256-Position Digital Potentiometer |
| AD5291 | 制造商:AD 制造商全稱:Analog Devices 功能描述:256-/1024-Position, DigiPOT+ Potentiometers with Maximum ±1% R-Tolerance Error and 20-TP Memory |
| AD5291BRUZ-100 | 制造商:Analog Devices 功能描述: |
| AD5291BRUZ-100-RL7 | 制造商:Analog Devices 功能描述: |
| AD5291BRUZ-20 | 功能描述:IC POT DIG 1024P SPI 20K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
發布緊急采購，3分鐘左右您將得到回復。