參數資料
型號： AD5292BRUZ-100-RL7
廠商： Analog Devices Inc
文件頁數： 19/32頁
文件大?。?/td> 0K
描述： IC DGTL POT 1024POS 20K 14TSSOP
設計資源： Variable Gain Noninverting Amplifier Using AD5292 and OP184 (CN0112)
Variable Gain Inverting Amplifier Using AD5292 and OP184 (CN0113)
Low Cost, High Voltage, Programmable Gain Instrumentation Amplifier Using AD5292 and AD8221 (CN0114)
Programmable High Voltage Source with Boosted Output Current Using AD5292, OP184, and MOSFETs (CN0115)
Programmable Bidirectional Current Source Using AD5292 and ADA4091-4 (CN0117)
Logarithmic Audio Volume Control with Glitch Reduction Using AD5292 (CN0120)
標準包裝： 1,000
接片： 1024
電阻（歐姆）： 100k
電路數： 1
溫度系數： 標準值 35 ppm/°C
存儲器類型： 非易失
接口： 4 線串行
電源電壓： 9 V ~ 33 V，±9 V ~ 16.5 V
工作溫度： -40°C ~ 105°C
安裝類型： 表面貼裝
封裝/外殼： 14-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 14-TSSOP
包裝： 帶卷 (TR)
AD5291/AD5292
Rev. D | Page 26 of 32
PROGRAMMING THE VARIABLE RESISTOR
Rheostat Operation—1% Resistor Tolerance
The AD5291 and AD5292 operate in rheostat mode when only
two terminals are used as a variable resistor. The unused
terminal can be left floating or tied to the W terminal, as shown in
W
A
B
W
A
B
W
A
B
0
7
67
4-
05
2
Figure 66. Rheostat Mode Configuration
The nominal resistance between Terminal A and Terminal B,
RAB, is available in 20 kΩ, 50 kΩ, and 100 kΩ, and 256 or 1024
tap points accessed by the wiper terminal. The 8-/10-bit data in
the RDAC latch is decoded to select one of the 256/1024
possible wiper settings. The AD5291 and AD5292 contain an
internal ±1% resistor performance mode that can be disabled or
enabled (this is enabled by default), by programming Bit C2 of
the control register (see Table 13 and Table 14). The digitally
programmed output resistance between the W terminal and the
A terminal, RWA, and between the W terminal and B terminal,
RWB, is internally calibrated to give a maximum of ±1% absolute
resistance error across a wide code range. As a result, the
general equations for determining the digitally programmed
output resistance between the W terminal and B terminal are
AD5291:
AB
WB
R
D
R
×
=
256
)
(
(1)
AD5292:
AB
WB
R
D
R
×
=
1024
)
(
(2)
where:
D is the decimal equivalent of the binary code loaded in the
8-/10-bit RDAC register.
RAB is the end-to-end resistance.
Similar to the mechanical potentiometer, the resistance of the
RDAC between the W terminal and the A terminal also produces a
digitally controlled complementary resistance, RWA. RWA is also
calibrated to give a maximum of 1% absolute resistance error.
RWA starts at the maximum resistance value and decreases as the
data loaded into the latch increases. The general equations for
this operation are
AD5291:
AB
WA
R
D
R
×
=
256
)
(
(3)
AD5292:
AB
WA
R
D
R
×
=
1024
)
(
(4)
where:
D is the decimal equivalent of the binary code loaded in the
8-/10-bit RDAC register.
RAB is the end-to-end resistance.
In the zero-scale condition, a finite total wiper resistance of 120 Ω
is present. Regardless of which setting the part is operating in,
take care to limit the current between Terminal A and Terminal B,
between Terminal W and Terminal A, and between Terminal W
and Terminal B, to the maximum continuous current of ±3 mA or
to the pulse current specified in Table 8. Otherwise, degradation
or possible destruction of the internal resistors may occur.
PROGRAMMING THE POTENTIOMETER DIVIDER
Voltage Output Operation
The digital potentiometer easily generates a voltage divider at
the wiper to B and at the wiper to A that is proportional to the
input voltage at A to B, as shown in Figure 67. Unlike the polarity
of VDD to GND, which must be positive, voltage across A to B,
W to A, and W to B can be at either polarity.
W
A
B
VIN
VOUT
07
67
4-
05
3
Figure 67. Potentiometer Mode Configuration
If ignoring the effect of the wiper resistance for simplicity, con-
necting the A terminal to 30 V and the B terminal to ground
produces an output voltage at the Wiper W to Terminal B
ranging from 0 V to 1 LSB less than 30 V. Each LSB of voltage is
equal to the voltage applied across Terminal A and Terminal B,
divided by the 256/1024 positions of the potentiometer divider.
The general equations defining the output voltage at VW with
respect to ground for any valid input voltage applied to Terminal A
and Terminal B are
AD5291:
B
A
W
V
D
V
D
V
×
+
×
=
256
)
(
(5)
AD5292:
B
A
W
V
D
V
D
V
×
+
×
=
1024
)
(
(6)
If using the AD5291 and AD5292 in voltage divider mode as
shown in Figure 67, then the ±1% resistor tolerance calibration
feature reduces the error when matching with discrete resistors.
However, it is recommended to disable the internal ±1% resistor
tolerance calibration feature by programming Bit C2 of the
control register (see Table 13 and Table 14) to optimize wiper
position update rate. In this configuration, the RDAC is ratiome-
tric and resistor tolerance error does not affect performance.
相關PDF資料
PDF描述
AD5292BRUZ-20-RL7 IC POT DIG 1024P SPI 20K 14TSSOP
DS1100U-200/T&R IC DELAY LINE 5TAP 200NS 8-USOP
VI-274-MW CONVERTER MOD DC/DC 48V 100W
AD7376ARWZ10-RL IC POT DIGITAL 10K 16-SOIC
DS1100U-30/T&R IC DELAY LINE 5TAP 30NS 8-USOP
相關代理商/技術參數
參數描述
AD5292BRUZ-20 功能描述:IC POT DIG 1024P SPI 20K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT
AD5292BRUZ-20-RL7 功能描述:IC POT DIG 1024P SPI 20K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR)
AD5292BRUZ-50 功能描述:IC DGTL POT 1024POS 20K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT
AD5292BRUZ-50-RL7 功能描述:IC DGTL POT 1024POS 20K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR)
AD5292SRU-20-EP 制造商:Analog Devices 功能描述:1024 TAP, 1% DIGIPOT WITH SPI INTERFACE - Rail/Tube 制造商:Analog Devices 功能描述:IC DGTL POT 1024POS 20K 14TSSOP 制造商:Analog Devices 功能描述:1024 tap 1% digiPOT with SPI interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*