參數資料
型號: AD5412ACPZ-REEL7
廠商: Analog Devices Inc
文件頁數: 20/44頁
文件大?。?/td> 0K
描述: IC DAC 12BIT SER 40-LFCSP
設計資源: Simplified 12-Bit Voltage and 4 mA-to-20 mA Output Solution Using AD5412 (CN0097)
標準包裝: 1
設置時間: 25µs
位數: 12
數據接口: MICROWIRE?,串行,SPI?
轉換器數目: 1
電壓電源: 模擬和數字,雙 ±
功率耗散(最大): 128mW
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 40-VFQFN 裸露焊盤,CSP
供應商設備封裝: 40-LFCSP-VQ(6x6)
包裝: 標準包裝
輸出數目和類型: 1 電流,單極;1 電流,雙極;1 電壓,單極;1 電壓,雙極
采樣率(每秒): 40k
產品目錄頁面: 782 (CN2011-ZH PDF)
其它名稱: AD5412ACPZ-REEL7DKR
Data Sheet
AD5412/AD5422
Rev. I | Page 27 of 44
THEORY OF OPERATION
The AD5412/AD5422 are precision digital-to-current loop and
voltage output converters designed to meet the requirements of
industrial process control applications. They provide a high
precision, fully integrated, low cost single-chip solution for
generating current loop and unipolar/bipolar voltage outputs.
Current ranges are 0 mA to 20 mA, 0 mA to 24 mA, and 4 mA
to 20 mA; the voltage ranges available are 0 V to 5 V, ±5 V, 0 V
to 10 V, and ±10 V; a 10% overrange is available on all voltage
output ranges. The current and voltage outputs are available on
separate pins, and only one is active at any time. The desired
output configuration is user selectable via the control register.
ARCHITECTURE
The DAC core architecture of the AD5412/AD5422 consists
of two matched DAC sections. A simplified circuit diagram is
shown in Figure 65. The four MSBs of the 12-/16-bit data-word
are decoded to drive 15 switches, E1 to E15. Each of these switches
connects one of 15 matched resistors to either ground or the
reference buffer output. The remaining 8/12 bits of the data-
word drive the S0 to S7/S11 switches of an 8-/12-bit voltage
mode R-2R ladder network.
8-12 BIT R-2R LADDER
FOUR MSBs DECODED INTO
15 EQUAL SEGMENTS
2R
S0
S1
S7/S11
E1
E2
E15
VOUT
2R
06996-
057
Figure 65. DAC Ladder Structure
The voltage output from the DAC core is either converted to
a current (see Figure 66) which is then mirrored to the supply
rail so that the application simply sees a current source output
with respect to ground or it is buffered and scaled to output a
software selectable unipolar or bipolar voltage range (see
Figure 67). The current and voltage are output on separate
pins and cannot be output simultaneously.
12-/16-BIT
DAC
A1
AVDD
IOUT
A2
T1
T2
RSET
R2
R3
06996-
058
Figure 66. Voltage-to-Current Conversion Circuitry
06996-
059
12-/16-BIT
DAC
RANGE
SCALING
VCM
REFIN
+VSENSE
VOUT
–VSENSE
R1
RLOAD
–1V TO +3V
AD5412/AD5422
Figure 67. Voltage Output
Voltage Output Amplifier
The voltage output amplifier is capable of generating both
unipolar and bipolar output voltages. It is capable of driving
a load of 1 k in parallel with 1 F (with an external compen-
sation capacitor) to GND. The source and sink capabilities of
the output amplifier can be seen in Figure 37. The slew rate
is 1 V/s with a full-scale settling time of 25 s maximum (10 V
step). Figure 67 shows the voltage output driving a load, RLOAD,
on top of a common-mode voltage (VCM) of 1 V to +3 V. In
output module applications where a cable could possibly
become disconnected from +VSENSE, resulting in the amplifier
loop being broken and possibly resulting in large destructive
voltages on VOUT, include an optional resistor (R1) between
+VSENSE and VOUT, as shown in Figure 67, of a value between
2 kΩ and 5 kΩ to ensure the amplifier loop is kept closed. If
remote sensing of the load is not required, connect +VSENSE
directly to VOUT and connect VSENSE directly to GND. When
changing ranges on the voltage output, a glitch may occur. For
this reason, it is recommended that the output be disabled by
setting the OUTEN bit of the control register to logic low before
changing the output voltage range; this prevents a glitch from
occurring.
Driving Large Capacitive Loads
The voltage output amplifier is capable of driving capacitive
loads of up to 1 F with the addition of a nonpolarized 4 nF
compensation capacitor between the CCOMP and VOUT pins.
Without the compensation capacitor, up to 20 nF capacitive
loads can be driven.
相關PDF資料
PDF描述
MS27497E22B2SB CONN RCPT 85POS WALL MNT W/SCKT
M83723/95W1412N CONN PLUG 12POS STRAIGHT W/SCKT
M83723/95R1412N CONN PLUG 12POS STRAIGHT W/SCKT
M83723/96R14126 CONN PLUG 12POS STRAIGHT W/PINS
M83723/95G14046 CONN PLUG 4POS STRAIGHT W/SCKT
相關代理商/技術參數
參數描述
AD5412AREZ 功能描述:IC DAC 12BIT SER 24TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散(最大):55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP(0.209",5.30mm 寬) 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流,單極;1 電流,雙極 采樣率(每秒):*
AD5412AREZ 制造商:Analog Devices 功能描述:IC DAC 12BIT TSSOP-24 制造商:Analog Devices 功能描述:IC, DAC, 12BIT, TSSOP-24
AD5412AREZ-REEL7 功能描述:IC DAC 12BIT SER 24-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?,串行,SPI? 轉換器數目:8 電壓電源:單電源 功率耗散(最大):2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP(4x3) 包裝:管件 輸出數目和類型:8 電壓,單極 采樣率(每秒):*
AD5412BCPZ 制造商:AD 制造商全稱:Analog Devices 功能描述:Single Channel, 12/16-Bit, Serial Input, Current Source & Voltage Output DAC
AD5412BREZ 制造商:Analog Devices 功能描述: