- 您現在的位置：買賣IC網 > PDF目錄373881 > AD5520JST-REEL (ANALOG DEVICES INC) Per Pin Parametric Measurement Unit/Source Measure Unit PDF資料下載
參數資料
| 型號： | AD5520JST-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Per Pin Parametric Measurement Unit/Source Measure Unit |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 封裝： | MS-026BCD, LQFP-64 |
| 文件頁數： | 11/20頁 |
| 文件大?。?/td> | 763K |
| 代理商： | AD5520JST-REEL |
REV. A
AD5520
–11–
THEORY OF OPERATION
The AD5520 is a single channel per pin parametric measurement
unit (PPMU) for use in semiconductor automatic test equip-
ment. It contains programmable modes to force a pin voltage and
measure the corresponding current (FVMI), force current mea-
sure voltage (FIMV), force current measure current (FIMI), and
force voltage measure voltage (FVMV). The PPMU can force or
measure a voltage from –11 V to +11 V. It can force or measure a
current over four ranges: 4
μ
A, 40
μ
A, 400
μ
A, and 4 mA. The
addition of an external driver allows two extended ranges.
The device provides a force sense capability to ensure accuracy
at the tester pin. A guard output is also available to drive the
shield of a force/sense pair.
The AD5520 has an on-board window comparator that pro-
vides two bits of useful information, DUT too low or too high.
Also provided on the chip is clamp circuitry that will flag via
CLHDETECT and CLLDETECT if the voltage applied to
FIN or across the DUT has exceeded the voltage applied to
CLL and CLH.
On chip is clamp circuitry that clamps the output of the force
amplifier if the voltage at MEASIOUT and MEASVOUT
exceeds CLL and CLH.
INTERFACE
The AD5520 PPMU is controlled via a number of digital inputs,
which are discussed in detail in the following sections. All inputs
are TTL compatible.
CS
is used to select the device while
STB
(active low input) latches data available on the other digital inputs
and updates any required digital outputs. The rising edge of
STB
triggers sequence inputs. The remaining digital inputs control the
function of the PMU—which measure mode it is in, which com-
pensation capacitor is used, and the selected current range.
Standby Mode
The AD5520 may be placed into standby mode via the standby
logic input. In this mode, the force amplifier is disconnected from
the force input (FIN), the switch in series with the force output
pins, FOHx, is opened, and the current measure amplifier is dis-
connected from the sense resistors. The voltage measure amplifier
is still connected across the DUT, so DUT voltage measure-
ments may still be made while in standby mode. Figure 3 shows
the configuration of the PMU while in standby mode.
Table I. Standby Mode
STANDBY
Function
Low
High
Normal Force Mode
Standby Mode
DAC
MEASIHx
MEASIL
MEASVH
MEASVL
FOHx
R
S
DUT
FIN
MEASIOUT
MEASVOUT
G = 16
G = 1
Figure 3. PMU in Standby Mode
Force Voltage or Force Current
FSEL is an input that determines whether the PPMU forces a
voltage or current.
Table II. FSEL Function
FSEL
Function
Low
Voltage Force and Current Clamp with
MEASIOUT Voltage
Current Force and Voltage Clamp with
MEASVOUT Voltage
High
Measured Parameter
MEASOUT is a muxed output that tracks the sensed parameter,
MSEL connects it to the output of either the current sense
amplifier or the voltage sense amplifier, depending on which is
the measured parameter of interest.
The MEASOUT pin will be connected back to an ADC to
allow the measured value to be converted to a digital code.
Table III. MEASOUT Connected to
Voltage or Current
MSEL
Function
Low
High
MEASOUT = DUT Voltage
MEASOUT = DUT Current
The MEASOUT pin may also be made high impedance through
the MOEB logic input.
Table IV. MOEB Allows MEASOUT
to Go High Impedance
MOEB
Function
Low
High
Enable MEASOUT Output
Hi-Z MEASOUT Output
相關PDF資料 |
PDF描述 |
|---|---|
| AD5530 | Serial Input, Voltage Output 12-/14-Bit DACs |
| AD5530BRU | ECONOLINE: RO & RE - Industry Standard Pinout- 1kVDC & 2kVDC Isolation- UL94V-0 Package Material- Toroidal Magnetics- Fully Encapsulated- Custom Solutions Available- Efficiency to 85% |
| AD5531 | Serial Input, Voltage Output 12-/14-Bit DACs |
| AD5531BRU | RE Series - Econoline Unregulated DC-DC Converters; Input Voltage (Vdc): 12V; Output Voltage (Vdc): 05V; Power: 1W; Industry Standard Pinout; 1kVDC & 2kVDC Isolation; UL94V-0 Package Material; Optional Continuous Short Circuit Protected; Fully Encapsulated; Custom Solutions Available; Efficiency to 85% |
| AD5532 | 32-Channel, 14-Bit Voltage-Output DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5520JSTZ | 功能描述:IC PPMU SNGL-CH 64-LQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
| AD5520JSTZ-REEL | 制造商:AD 制造商全稱:Analog Devices 功能描述:Per Pin Parametric Measurement Unit/Source Measure Unit |
| AD5520JSTZ-REEL1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Per Pin Parametric Measurement Unit/Source Measure Unit |
| AD5521JST | 制造商:Analog Devices 功能描述: |
| AD5521JSTZ | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。