參數資料
型號: AD5662ARM-1
廠商: Analog Devices Inc
文件頁數: 13/24頁
文件大小: 0K
描述: IC DAC 16BIT BUFF V-OUT 8-MSOP
產品培訓模塊: Data Converter Fundamentals
DAC Architectures
設計資源: 4 mA to 20 mA Process Control Loop Using AD5662 (CN0009)
16-Bit Fully Isolated Voltage Output Module Using AD5662, ADuM1401, and External Amplifiers (CN0063)
16-Bit Fully Isolated 4 mA to 20 mA Output Module Using AD5662, ADuM1401, and External Amplifiers (CN0064)
標準包裝: 50
系列: nanoDAC™
設置時間: 8µs
位數: 16
數據接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
轉換器數目: 1
電壓電源: 單電源
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 8-TSSOP,8-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 8-MSOP
包裝: 管件
輸出數目和類型: 1 電壓,單極
AD5662
Rev. A | Page 20 of 24
USING AD5662 WITH A
GALVANICALLY ISOLATED INTERFACE
In process-control applications in industrial environments, it is
often necessary to use a galvanically isolated interface to protect
and isolate the controlling circuitry from any hazardous
common-mode voltages that might occur in the area where the
DAC is functioning. Isocouplers provide isolation in excess of
3 kV. The AD5662 uses a 3-wire serial logic interface, so the
ADuM130x 3-channel digital isolator provides the required
isolation (see Figure 44). The power supply to the part also
needs to be isolated, which is done by using a transformer. On
the DAC side of the transformer, a 5 V regulator provides the
5 V supply required for the AD5662.
0.1
μF
+5V
REGULATOR
GND
04777-033
DIN
SYNC
SCLK
POWER
10
μF
SDI
SCLK
DATA
AD5662
VOUT
VOB
VOC
VDD
V1C
V1B
V1A
ADMu103x
Figure 44. AD5662 with a Galvanically Isolated Interface
POWER SUPPLY BYPASSING AND GROUNDING
When accuracy is important in a circuit, it is helpful to carefully
consider the power supply and ground return layout on the
board. The printed circuit board containing the AD5662 should
have separate analog and digital sections, each having its own
area of the board. If the AD5662 is in a system where other
devices require an AGND-to-DGND connection, the connection
should be made at one point only. This ground point should be
as close as possible to the AD5662.
The power supply to the AD5662 should be bypassed with 10 μF
and 0.1 μF capacitors. The capacitors should be located as close
as possible to the device, with the 0.1 μF capacitor ideally right
up against the device. The 10 μF capacitors are the tantalum
bead type. It is important that the 0.1 μF capacitor has low
effective series resistance (ESR) and effective series inductance
(ESI), for example, common ceramic types of capacitors. This
0.1 μF capacitor provides a low impedance path to ground for
high frequencies caused by transient currents due to internal
logic switching.
The power supply line itself should have as large a trace as
possible to provide a low impedance path and to reduce glitch
effects on the supply line. Clocks and other fast switching
digital signals should be shielded from other parts of the board
by digital ground. Avoid crossover of digital and analog signals
if possible. When traces cross on opposite sides of the board,
ensure that they run at right angles to each other to reduce
feedthrough effects through the board. The best board layout
technique is the microstrip technique where the component
side of the board is dedicated to the ground plane only and the
signal traces are placed on the solder side. However, this is not
always possible with a 2-layer board.
相關PDF資料
PDF描述
AD5439YRU IC DAC DUAL 10BIT MULT 16-TSSOP
SY89834UMI IC CLK BUF MUX TRNSLA 2:4 16-MLF
AD5060ARJZ-2REEL7 IC DAC 16BIT SPI/SRL SOT23-8
VI-J0V-MY CONVERTER MOD DC/DC 5.8V 50W
VE-JTK-MX-B1 CONVERTER MOD DC/DC 40V 75W
相關代理商/技術參數
參數描述
AD5662ARM-1REEL7 功能描述:IC DAC 16BIT BUFF V-OUT 8-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?,串行,SPI? 轉換器數目:8 電壓電源:單電源 功率耗散(最大):2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP(4x3) 包裝:管件 輸出數目和類型:8 電壓,單極 采樣率(每秒):*
AD5662ARMZ-1 功能描述:IC DAC 16BIT BUFF V-OUT 8-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散(最大):- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP,8-MSOP(0.118",3.00mm 寬) 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓,單極 采樣率(每秒):* 產品目錄頁面:1398 (CN2011-ZH PDF)
AD5662ARMZ-1REEL7 功能描述:IC DAC 16BIT SGL 3/5V 8-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?,串行,SPI? 轉換器數目:8 電壓電源:單電源 功率耗散(最大):2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP(4x3) 包裝:管件 輸出數目和類型:8 電壓,單極 采樣率(每秒):*
AD5662BRJ-1 制造商:AD 制造商全稱:Analog Devices 功能描述:2.7 V to 5.5 V, 250 ??A, Rail-to-Rail Output 16-Bit DAC D/A in a SOT-23
AD5662BRJ-1500RL7 功能描述:IC DAC 16BIT BUFF V-OUT SOT23-8 RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?,串行,SPI? 轉換器數目:8 電壓電源:單電源 功率耗散(最大):2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP(4x3) 包裝:管件 輸出數目和類型:8 電壓,單極 采樣率(每秒):*