- 您現在的位置：買賣IC網 > PDF目錄8960 > AD5764BSUZ (Analog Devices Inc)IC DAC 16BIT QUAD VOUT 32-TQFP PDF資料下載
參數資料
| 型號： | AD5764BSUZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 16BIT QUAD VOUT 32-TQFP |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 產品變化通告： | AD5764(R), AD5744R Product Change 04/Sept/2009 |
| 設計資源： | High Accuracy, Bipolar Voltage Output Digital-to-Analog Conversion Using AD5764 (CN0006) |
| 標準包裝： | 1 |
| 設置時間： | 8µs |
| 位數： | 16 |
| 數據接口： | 串行 |
| 轉換器數目： | 4 |
| 電壓電源： | 雙 ± |
| 功率耗散（最大）： | 275 mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-TQFP |
| 供應商設備封裝： | 32-TQFP（7x7） |
| 包裝： | 托盤 |
| 輸出數目和類型： | 4 電壓，雙極 |
| 采樣率（每秒）： | 1.26M |
| 產品目錄頁面： | 784 (CN2011-ZH PDF) |
| 配用： | EVAL-AD5764EBZ-ND - BOARD EVAL FOR AD5764 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD5764
Data Sheet
Rev. F | Page 18 of 28
THEORY OF OPERATION
The AD5764 is a quad, 16-bit, serial input, bipolar voltage output
DAC and operates from supply voltages of ±11.4 V to ±16.5 V and
has a buffered output voltage of up to ±10.5263 V. Data is written to
the AD5764 in a 24-bit word format, via a 3-wire serial interface.
The device also offers an SDO pin that is available for daisy-
chaining or readback.
The AD5764 incorporates a power-on reset circuit, which ensures
that the data register powers up loaded with 0x0000. The AD5764
features a digital I/O port that can be programmed via the serial
interface, on-chip reference buffers and per channel digital gain,
and offset registers.
DAC ARCHITECTURE
The DAC architecture of the AD5764 consists of a 16-bit,
current mode, segmented R-2R DAC. The simplified circuit
diagram for the DAC section is shown in Figure 32.
The four MSBs of the 16-bit data word are decoded to drive
15 switches, E1 to E15. Each of these switches connects one of
the 15 matched resistors to either AGNDx or IOUT. The remain-
ing 12 bits of the data-word drive Switch S0 to Switch S11 of
the 12-bit R-2R ladder network.
05
30
3-
0
60
2R
E15
VREF
2R
E14
E1
2R
S11
RR
R
2R
S10
2R
12-BIT, R-2R LADDER
4 MSBs DECODED INTO
15 EQUAL SEGMENTS
VOUTx
2R
S0
2R
AGNDx
R/8
IOUT
Figure 32. DAC Ladder Structure
REFERENCE BUFFERS
The AD5764 operates with an external reference. The reference
inputs (REFAB and REFCD) have an input range up to 7 V. This
input voltage is used to provide a buffered positive and negative
reference for the DAC cores. The positive reference is given by
+VREF = 2 × VREF
The negative reference to the DAC cores is given by
VREF = 2 × VREF
These positive and negative reference voltages (along with the
gain register values) define the output ranges of the DACs.
SERIAL INTERFACE
The AD5764 is controlled over a versatile 3-wire serial interface
that operates at clock rates of up to 30 MHz and is compatible
with SPI, QSPI, MICROWIRE, and DSP standards.
Input Shift Register
The input shift register is 24 bits wide. Data is loaded into the
device MSB first as a 24-bit word under the control of a serial
clock input, SCLK. The input shift register consists of a read/
write bit, three register select bits, three DAC address bits, and
16 data bits, as shown in Table 9. The timing diagram for this
operation is shown in Figure 2.
Upon power-up, the data register is loaded with zero code
(0x0000), and the outputs are clamped to 0 V via a low imped-
ance path. The outputs can be updated with the zero code value
at this time by asserting either LDAC or CLR. The corresponding
output voltage depends on the state of the BIN/2sCOMP pin. If
the BIN/2sCOMP pin is tied to DGND, the data coding is twos
complement, and the outputs update to 0 V. If the BIN/2sCOMP
pin is tied to DVCC, the data coding is offset binary, and the
outputs update to negative full scale. To power up the outputs
with zero code loaded to the outputs, hold the CLR pin low
during power-up.
Standalone Operation
The serial interface works with both a continuous and noncon-
tinuous serial clock. A continuous SCLK source can only be
used if SYNC is held low for the correct number of clock cycles.
In gated clock mode, a burst clock containing the exact number
of clock cycles must be used and SYNC must be taken high after
the final clock to latch the data. The first falling edge of SYNC
starts the write cycle. Exactly 24 falling clock edges must be
applied to SCLK before SYNC is brought high again. If SYNC is
brought high before the 24th falling SCLK edge, the data written
is invalid. If more than 24 falling SCLK edges are applied before
SYNC is brought high, the input data is also invalid. The input
shift register addressed is updated on the rising edge of SYNC.
For another serial transfer to take place, SYNC must be brought
low again. After the end of the serial data transfer, data is
automatically transferred from the input shift register to the
addressed register.
When the data has been transferred into the chosen register of
the addressed DAC, the data register and outputs can be
updated by taking LDAC low.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J53-MZ-F4 | CONVERTER MOD DC/DC 24V 25W |
| AD7568BSZ | IC DAC 12BIT OCTAL LC2MOS 44MQFP |
| VI-B4Z-MU-F2 | CONVERTER MOD DC/DC 2V 80W |
| D38999/20KG41PB | CONN RCPT 41POS WALL MNT W/PINS |
| VI-B4Y-MU-F4 | CONVERTER MOD DC/DC 3.3V 132W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5764BSUZ-REEL7 | 功能描述:IC DAC 16BIT QUAD VOUT 32-TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k |
| AD5764CSU | 制造商:Analog Devices 功能描述: |
| AD5764CSUZ | 功能描述:IC DAC 16BIT QUAD VOUT 32TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD5764CSUZ-REEL7 | 功能描述:IC DAC 16BIT QUAD BIPO 32-TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD5764R | 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete Quad, 16-Bit, High Accuracy, Serial Input, Bipolar Voltage Output DAC |
發布緊急采購，3分鐘左右您將得到回復。