- 您現在的位置：買賣IC網 > PDF目錄16923 > AD604-EVALZ (Analog Devices Inc)BOARD EVAL FOR AD604 AMP PDF資料下載
參數資料
| 型號： | AD604-EVALZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 8/33頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD604 AMP |
| 標準包裝： | 1 |
| 系列： | X-AMP® |
| 每 IC 通道數： | 2 - 雙 |
| 放大器類型： | 可變增益 |
| 輸出類型： | 單端 |
| 轉換速率： | 170 V/µs |
| -3db帶寬： | 40MHz |
| 電流 - 輸出 / 通道： | 40mA |
| 工作溫度： | -40°C ~ 85°C |
| 電流供應（主 IC）： | 32mA |
| 板類型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | AD604 |
| 相關產品： | AD604ARZ-RL-ND - IC AMP VGA DUAL ULN 40MA 24SOIC AD604ANZ-ND - IC AMP VGA DUAL ULN 40MA 24DIP AD604ARSZ-R7-ND - IC AMP VGA DUAL ULN 40MA 24SSOP AD604ARSZ-RL-ND - IC AMP VGA DUAL ULN 40MA 24SSOP AD604ARSZ-ND - IC AMP VGA DUAL ULN 40MA 24SSOP AD604ARZ-ND - IC AMP VGA DUAL ULN 40MA 24SOIC AD604AR-REEL-ND - IC AMP VGA DUAL ULN 40MA 24SOIC AD604AR-ND - IC AMP VGA DUAL ULN 40MA 24SOIC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
AD604
Rev. G | Page 15 of 32
The larger portion of the input referred voltage noise comes
from the amplifier with 0.63 nV/√Hz. The current noise is
independent of gain and depends only on the bias current in
the input stage of the preamplifier, which is 3 pA/√Hz.
A unique circuit technique is used to interpolate continuously
among the tap points, thereby providing continuous attenuation
from 0 dB to 48.36 dB. The ladder network, together with the
interpolation mechanism, can be considered a voltage-controlled
potentiometer.
The preamplifier can drive 40 Ω (the nominal feedback resistors)
and the following 175 Ω ladder load of the DSX with low
distortion. For example, at 10 MHz and 1 V at the output, the
preamplifier has less than 45 dB of second and third harmonic
distortion when driven from a low (25 Ω) source resistance.
Because the DSX circuit uses a single voltage power supply, the
input biasing is provided by the VOCM buffer driving the MID
node (see Figure 41). Without internal biasing, the user would
have to dc bias the inputs externally. If not done carefully, the
biasing network can introduce additional noise and offsets. By
providing internal biasing, the user is relieved of this task and
only needs to ac-couple the signal into the DSX. Note that the
input to the DSX is still fully differential if driven differentially;
that is, Pin +DSXx and Pin DSXx see the same signal but with
opposite polarity (see the Ultralow Noise, Differential Input-
Differential Output VGA section).
In applications that require more than 48 dB of gain range, two
AD604 channels can be cascaded. Because the preamplifier has
a limited input signal range and consumes over half (120 mW)
of the total power (220 mW), and its ultralow noise is not necessary
after the first AD604 channel, a shutdown mechanism that
disables only the preamplifier is provided. To shut down the
preamplifier, connect the COM1 pin and/or COM2 pin to the
positive supply; the DSX is unaffected. For additional details,
refer to the Applications Information section.
What changes is the load seen by the driver; it is 175 Ω when
each input is driven single-ended but 350 Ω when driven
differentially. This is easily explained by thinking of the ladder
network as two 175 Ω resistors connected back-to-back with
the middle node, MID, being biased by the VOCM buffer. A
differential signal applied between the +DSXx and DSXx
nodes results in zero current into the MID node, but a single-
ended signal applied to either input, +DSXx or –DSXx, while
the other input is ac-grounded causes the current delivered by
the source to flow into the VOCM buffer via the MID node.
12
11
10
9
8
1
2
3
4
7
6
5
13
16
15
14
24
23
22
21
20
19
18
17
AD604
–DSX1
+DSX1
PAI1
FBK1
PAO1
COM1
COM2
PAI2
FBK2
PAO2
+DSX2
–DSX2
VGN1
VREF
VPOS
GND1
OUT1
VNEG
VPOS
GND2
OUT2
VOCM
VGN2
00
54
0-
04
0
The ladder resistor value of 175 Ω provides the optimum
balance between the load driving capability of the preamplifier
and the noise contribution of the resistors. An advantage of the
X-AMP architecture is that the output referred noise is constant
vs. gain over most of the gain range. Figure 41 shows that the
tap resistance is equal for all taps after only a few taps away
from the inputs. The resistance seen looking into each tap is
54.4 Ω, which makes 0.95 nV/√Hz of Johnson noise spectral
density. Because there are two attenuators, the overall noise
contribution of the ladder network is √2 times 0.95 nV/√Hz
or 1.34 nV/√Hz, a large fraction of the total DSX noise. The
balance of the DSX circuit components contributes another
1.2 nV/√Hz, which together with the attenuator produces
1.8 nV/√Hz of total DSX input referred noise.
Figure 40. Shutdown of Preamplifiers Only
DIFFERENTIAL LADDER (ATTENUATOR)
The attenuator before the fixed-gain amplifier of the DSX is
realized by a differential 7-stage R-1.5R resistive ladder network
with an untrimmed input resistance of 175 Ω single-ended or
350 Ω differential. The signal applied at the input of the ladder
network is attenuated by 6.908 dB per tap; thus, the attenuation
at the first tap is 0 dB, at the second, 13.816 dB, and so on, all
the way to the last tap where the attenuation is 48.356 dB
(see Figure 41).
R
–6.908dB
R
1.5R
RR
–13.82dB
–20.72dB
–27.63dB
–34.54dB
–41.45dB
–48.36dB
+DSXx
MID
–DSXx
NOTES
1. R = 96
2. 1.5R = 144
R
1.5R
175
00
54
0-
04
1
Figure 41. R-1.5R Dual Ladder Network
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2566-1YM | IC PCMCIA/CARDBUS SGL 14-SOP |
| AD8337-EVALZ-SS | BOARD EVALUATION FOR AD8337 SS |
| AD8264-EVALZ | BOARD EVAL FOR AD8264 VGA |
| X60003BIG3Z-50T1 | IC VREF SERIES PREC 5V SOT-23-3 |
| 381LX471M450A052 | CAP ALUM 470UF 450V 20% SNAP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD605 | 制造商:Analog Devices 功能描述: |
| AD605_06 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual, Low Noise, Single-Supply Variable Gain Amplifier |
| AD605_07 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual, Low Noise, Single-Supply Variable Gain Amplifier |
| AD605-00E | 功能描述:SENSOR MAG SW 40G STANDRD 8-MSOP 制造商:nve corp/sensor products 系列:AD 包裝:管件 零件狀態:有效 功能:全極開關 技術:霍爾效應 極化:任意一種 感應范圍:±5mT 跳閘，±2.5mT 釋放 測試條件:-40°C ~ 125°C 電壓 - 電源:4.5 V ~ 30 V 電流 - 電源（最大值）:4.5mA 電流 - 輸出（最大值）:20mA 輸出類型:開路集電極 特性:- 工作溫度:-40°C ~ 125°C（TA） 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商器件封裝:8-MSOP 標準包裝:1,000 |
| AD605-02E | 功能描述:SENSOR MAG SW 40G STANDARD 8SOIC 制造商:nve corp/sensor products 系列:AD 包裝:管件 零件狀態:有效 功能:全極開關 技術:霍爾效應 極化:任意一種 感應范圍:±5mT 跳閘，±2.5mT 釋放 測試條件:-40°C ~ 125°C 電壓 - 電源:4.5 V ~ 30 V 電流 - 電源（最大值）:4.5mA 電流 - 輸出（最大值）:20mA 輸出類型:開路集電極 特性:- 工作溫度:-40°C ~ 125°C（TA） 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SOIC 標準包裝:1,000 |
發布緊急采購，3分鐘左右您將得到回復。