參數資料
| 型號： | AD623BRZ-RL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 8/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP INST R-R LP 8SOIC |
| 標準包裝： | 2,500 |
| 放大器類型： | 儀表 |
| 電路數： | 1 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 0.3 V/µs |
| -3db帶寬： | 800kHz |
| 電流 - 輸入偏壓： | 17nA |
| 電壓 - 輸入偏移： | 25µV |
| 電流 - 電源： | 375µA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 12 V，± 2.5 V ~ 6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 帶卷 (TR) |
AD623
Rev. D | Page 16 of 24
APPLICATIONS INFORMATION
BASIC CONNECTION
the AD623. The +VS and VS terminals are connected to the
power supply. The supply can be either bipolar (VS = ±2.5 V to
±6 V) or single supply (VS = 0 V, +VS = 3.0 V to 12 V). Power
supplies should be capacitively decoupled close to the power pins of
the device. For the best results, use surface-mount 0.1 μF ceramic
chip capacitors and 10 μF electrolytic tantalum capacitors.
0
077
8-
0
42
RG
VIN
OUTPUT
VOUT
REF
RG
REF (INPUT)
+2.5V TO +6V
+VS
10F
0.1F
–2.5V TO –6V
–VS
10F
0.1F
Figure 42. Dual-Supply Basic Connection
00
77
8-
0
55
RG
VIN
OUTPUT
VOUT
REF
RG
REF (INPUT)
+3V TO +12V
+VS
10F
0.1F
Figure 43. Single-Supply Basic Connection
The input voltage, which can be either single-ended (tie either
IN or +IN to ground), or differential is amplified by the
programmed gain. The output signal appears as the voltage
difference between the OUTPUT pin and the externally applied
voltage on the REF input. For a ground-referenced output, REF
should be grounded.
GAIN SELECTION
The gain of the AD623 is resistor programmed by RG, or more
precisely, by whatever impedance appears between Pin 1 and
Pin 8. The AD623 is designed to offer accurate gains using 0.1%
to 1% tolerance resistors. Table 5 shows the required values of
RG for the various gains. Note that for G = 1, the RG terminals
are unconnected (RG = ∞). For any arbitrary gain, RG can be
calculated by
RG
= 100 kΩ/(G 1)
REFERENCE TERMINAL
The reference terminal potential defines the zero output voltage
and is especially useful when the load does not share a precise
ground with the rest of the system. It provides a direct means of
injecting a precise offset to the output. The reference terminal is
also useful when bipolar signals are being amplified because it
can be used to provide a virtual ground voltage. The voltage on
the reference terminal can be varied from VS to +VS.
Table 5. Required Values of Gain Resistors
Desired Gain
1% Standard Table Value of RG (Ω)
Calculated Gain Using 1% Resistors
2
100 k
2
5
24.9 k
5.02
10
11 k
10.09
20
5.23 k
20.12
33
3.09 k
33.36
40
2.55 k
40.21
50
2.05 k
49.78
65
1.58 k
64.29
100
1.02 k
99.04
200
499
201.4
500
200
501
1000
100
1001
相關PDF資料 |
PDF描述 |
|---|---|
| SMBJ6.0CAHE3/5B | TVS BIDIR 600W 6V 5% SMB |
| SMBJ64CAHE3/5B | TVS BIDIR 600W 64V 5% SMB |
| TSW-141-26-G-S | CONN HEADER 41POS .100" SGL GOLD |
| OP184ES-REEL | IC OPAMP GP R-R 4.25MHZ LN 8SOIC |
| SMBJ60CAHE3/5B | TVS BIDIR 600W 60V 5% SMB |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD623-EVAL | 制造商:Analog Devices 功能描述:Evaluation Board For The AD623 Converts A Differential Signal To A Single-Ended Signal |
| AD624 | 制造商:AD 制造商全稱:Analog Devices 功能描述:10 MHz, 20 V/レs, G = 1, 10, 100, 1000 i CMOS㈢ Programmable Gain Instrumentation Amplifier |
| AD624-00 | 制造商:RHOPOINT 制造商全稱:RHOPOINT COMPONENTS 功能描述:GMR Digital Sensor Evaluation Kit |
| AD624-00E | 功能描述:SENSOR MAG SW 28G CROS AX 8-MSOP 制造商:nve corp/sensor products 系列:AD 包裝:管件 零件狀態(tài):有效 功能:全極開關 技術:霍爾效應 極化:任意一種 感應范圍:±3.4mT 跳閘，±1.4mT 釋放 測試條件:-40°C ~ 125°C 電壓 - 電源:4.5 V ~ 30 V 電流 - 電源（最大值）:4.5mA 電流 - 輸出（最大值）:20mA 輸出類型:開路集電極 特性:- 工作溫度:-40°C ~ 125°C（TA） 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商器件封裝:8-MSOP 標準包裝:1,000 |
| AD624-02E | 功能描述:SENSOR MAG SW 28G CROS AXS 8SOIC 制造商:nve corp/sensor products 系列:AD 包裝:管件 零件狀態(tài):有效 功能:全極開關 技術:霍爾效應 極化:任意一種 感應范圍:±3.4mT 跳閘，±1.4mT 釋放 測試條件:-40°C ~ 125°C 電壓 - 電源:4.5 V ~ 30 V 電流 - 電源（最大值）:4.5mA 電流 - 輸出（最大值）:20mA 輸出類型:開路集電極 特性:- 工作溫度:-40°C ~ 125°C（TA） 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SOIC 標準包裝:1,000 |
發(fā)布緊急采購，3分鐘左右您將得到回復。