- 您現在的位置：買賣IC網 > PDF目錄373896 > AD725AR (ANALOG DEVICES INC) Low Cost RGB to NTSC/PAL Encoder with Luma Trap Port PDF資料下載
參數資料
| 型號： | AD725AR |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 顏色信號轉換 |
| 英文描述： | Low Cost RGB to NTSC/PAL Encoder with Luma Trap Port |
| 中文描述： | COLOR SIGNAL ENCODER, PDSO16 |
| 封裝： | SOIC-16 |
| 文件頁數： | 11/20頁 |
| 文件大?。?/td> | 347K |
| 代理商： | AD725AR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
AD725
REV. 0
–11–
T he AD725 will operate with subcarrier frequencies that deviate
quite far from those specified by the T V standards. However,
the monitor will in general not be quite so forgiving. Most moni-
tors can tolerate a subcarrier frequency that deviates several hun-
dred Hz from the nominal standard without any degradation in
picture quality. T hese conditions imply that the subcarrier fre-
quency accuracy is a system specification and not a specification
of the AD725 itself.
T he ST ND pin is used to select between NT SC and PAL opera-
tion. Various blocks inside the AD725 use this input to program
their operation. Most of the more common variants of NT SC and
PAL are supported. T here are, however, two known specific stan-
dards which are not supported by the standard AD725. T hese are
NTSC 4.43 and M-PAL.
Basically these two standards use most of the features of the
standard that their names imply, but use the subcarrier that is
equal to or approximately equal to the frequency of the other
standard. Because of the automatic programming of the filters in
the chrominance path and other timing considerations, a factory-
programmed special version of the AD725 is necessary to sup-
port these standards.
Layout Considerations
T he AD725 is an all CMOS mixed signal part. It has separate
pins for the analog and digital +5 V and ground power supplies.
Both the analog and digital ground pins should be tied to the
ground plane by a short, low inductance path. Each power
supply pin should be bypassed to ground by a low inductance
0.1
μ
F capacitor and a larger tantalum capacitor of about 10
μ
F.
T he three analog inputs (RIN, GIN, BIN) should be terminated
with 75
to ground close to the respective pins. However, as
these are high impedance inputs, they can be in a loop-through
configuration. T his technique is used to drive two or more
devices with high frequency signals that are separated by some
distance. A connection is made to the AD725 with no local
termination, and the signals are run to another distant device
where the termination for these signals is provided.
T he output amplitudes of the AD725 are double that required
by the devices that it drives. T his compensates for the halving of
the signal levels by the required terminations. A 75
series
resistor is required close to each AD725 output, while 75
to
ground should terminate the far end of each line.
T he outputs have a dc bias and must be ac coupled for proper
operation. T he COMP and LUMA outputs have information
down to 30 Hz for NT SC (25 MHz for PAL) that must be trans-
mitted. Each output requires a 220
μ
F series capacitor to work
with the 75
resistance to pass these low frequencies. T he CRMA
signal has information mostly up at the chroma frequency and
can use a smaller capacitor if desired, but 220
μ
F can be used to
minimize the number of different components used in the design.
APPLY ING T HE AD725
Inputs
RIN, BIN, GIN are analog inputs that should be terminated to
ground with 75
in close proximity to the IC. When properly
terminated the peak-to-peak voltage for a maximum input level
should be 714 mV p-p. T he horizontal blanking interval should
be the most negative part of each signal.
T he inputs should be held at the input signal’s black level dur-
ing the horizontal blanking interval. T he internal dc clamps will
clamp this level during color burst to a reference that is used
internally as the black level. Any noise present on the RIN,
GIN, BIN or AGND pins during this interval will be sampled
onto the input capacitors. T his can result in varying dc levels
from line to line in all outputs, or if imbalanced, subcarrier
feedthrough in the COMP and CRMA outputs.
For increased noise rejection, larger input capacitors are desired.
A capacitor of 0.1
μ
F is usually adequate.
Similarly, the U and V clamps balance the modulators during an
interval shortly after the falling CSYNC input. Noise present
during this interval will be sampled in the modulators, resulting
in residual subcarrier in the COMP and CRMA outputs.
HSYNC and VSYNC are two logic level inputs that are com-
bined internally to produce a composite sync signal. If a com-
posite sync signal is to be used, it can be input to HSYNC while
VSYNC is pulled to logic HI (> +2 V).
T he form of the input sync signal(s) will determine the form of
the composite sync on the composite video (COMP) and lumi-
nance (LUMA) outputs. If no equalization or serration pulses
are included in the HSYNC input there won’t be any in the
outputs. Although sync signals without equalization and serra-
tion pulses do not technically meet the video standards’ specifi-
cations, many monitors do not require these pulses in order to
display good pictures. T he decision whether to include these
signals is a system trade-off between cost and complexity and
adhering strictly to the video standards.
T he HSYNC and VSYNC logic inputs have a small amount of
built-in hysteresis to avoid interpreting noisy input edges as
multiple sync edges. T his is critical to proper device operation, as
the sync pulses are timed for vertical blanking interval detection.
T he logic inputs have been designed for VIL < 1.0 V and VIH
> 2.0 V for the entire temperature and supply range of opera-
tion. T his allows the AD725 to directly interface to T T L or 3 V
CMOS compatible outputs, as well as 5 V CMOS outputs
where VOL is less than 1.0 V.
T he NT SC specification calls for a frequency accuracy of
±
10 Hz
from the nominal subcarrier frequency of 3.579545 MHz. While
maintaining this accuracy in a broadcast studio might not be a
severe hardship, it can be quite expensive in a low cost con-
sumer application.
相關PDF資料 |
PDF描述 |
|---|---|
| AD725 | Low Cost RGB to NTSC/PAL Encoder with Luma Trap Port(低成本RGB-NTSC/PAL編碼器) |
| AD7266 | Differential Input, Dual 2 MSPS, 12-Bit, 3-Channel SAR ADC |
| AD7266ACP | Differential Input, Dual 2 MSPS, 12-Bit, 3-Channel SAR ADC |
| AD7266ASU | Differential Input, Dual 2 MSPS, 12-Bit, 3-Channel SAR ADC |
| AD7266BCP | Differential Input, Dual 2 MSPS, 12-Bit, 3-Channel SAR ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD725AR-REEL | 制造商:Analog Devices 功能描述:RGB to NTSC and PAL Encoder 16-Pin SOIC W T/R 制造商:Rochester Electronics LLC 功能描述:SOIC LOW COST VIDEO ENCODER - Tape and Reel |
| AD725AR-REEL7 | 制造商:Analog Devices 功能描述:RGB to NTSC and PAL Encoder 16-Pin SOIC W T/R 制造商:Rochester Electronics LLC 功能描述:SOIC LOW COST VIDEO ENCODER - Tape and Reel |
| AD725ARZ | 功能描述:IC ENCODER RGB TO NTSC 16-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 編碼器，解碼器，轉換器 系列:- 產品變化通告:Development Systems Discontinuation 26/Apr/2011 標準包裝:1 系列:- 類型:編碼器 應用:DVB-S.2 系統 電壓 - 電源，模擬:- 電壓 - 電源，數字:- 安裝類型:- 封裝/外殼:模塊 供應商設備封裝:模塊 包裝:散裝 其它名稱:Q4645799 |
| AD725ARZ | 制造商:Analog Devices 功能描述:Video IC |
| AD725ARZ-R7 | 功能描述:IC ENCODER RGB TO NTSC 16-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 編碼器，解碼器，轉換器 系列:- 產品變化通告:Development Systems Discontinuation 26/Apr/2011 標準包裝:1 系列:- 類型:編碼器 應用:DVB-S.2 系統 電壓 - 電源，模擬:- 電壓 - 電源，數字:- 安裝類型:- 封裝/外殼:模塊 供應商設備封裝:模塊 包裝:散裝 其它名稱:Q4645799 |
發布緊急采購，3分鐘左右您將得到回復。