- 您現在的位置：買賣IC網 > PDF目錄10316 > AD7327BRUZ-REEL (Analog Devices Inc)IC ADC 12BIT+SAR 8CHAN 20-TSSOP PDF資料下載
參數資料
| 型號： | AD7327BRUZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 28/37頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT+SAR 8CHAN 20-TSSOP |
| 標準包裝： | 2,500 |
| 位數： | 12 |
| 采樣率（每秒）： | 500k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 17mW |
| 電壓電源： | 雙 ± |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 8 個單端，單極；8 個單端，雙極；4 個差分，單極；4 個差分，雙極 |
| 配用： | EVAL-AD7327CBZ-ND - BOARD EVALUATION FOR AD7327 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
Data Sheet
AD7327
Rev. B | Page 33 of 36
APPLICATION HINTS
LAYOUT AND GROUNDING
The printed circuit board that houses the AD7327 should be
designed so that the analog and digital sections are confined to
certain areas of the board. This design facilitates the use of
ground planes that can easily be separated.
To provide optimum shielding for ground planes, a minimum
etch technique is generally best. All AGND pins on the AD7327
should be connected to the AGND plane. Digital and analog
ground pins should be joined in only one place. If the AD7327
is in a system where multiple devices require an AGND and
DGND connection, the connection should still be made at only
one point. A star point should be established as close as possible
to the ground pins on the AD7327.
Good connections should be made to the power and ground
planes. This can be done with a single via or multiple vias for
each supply and ground pin.
Avoid running digital lines under the AD7327 device because
this couples noise onto the die. However, the analog ground
plane should be allowed to run under the AD7327 to avoid
noise coupling. The power supply lines to the AD7327 device
should use as large a trace as possible to provide low impedance
paths and reduce the effects of glitches on the power supply line.
To avoid radiating noise to other sections of the board, com-
ponents, such as clocks, with fast switching signals should be
shielded with digital ground and never run near the analog inputs.
Avoid crossover of digital and analog signals. To reduce the effects
of feedthrough within the board, traces should be run at right
angles to each other. A microstrip technique is the best method,
but its use may not be possible with a double-sided board. In
this technique, the component side of the board is dedicated to
ground planes, and signals are placed on the other side.
Good decoupling is also important. All analog supplies should
be decoupled with 10 F tantalum capacitors in parallel with
0.1 F capacitors to AGND. To achieve the best results from
these decoupling components, they must be placed as close as
possible to the device, ideally right up against the device. The
0.1 F capacitors should have a low effective series resistance
(ESR) and low effective series inductance (ESI), such as is
typical of common ceramic and surface mount types of
capacitors. These low ESR, low ESI capacitors provide a low
impedance path to ground at high frequencies to handle
transient currents due to internal logic switching.
POWER SUPPLY CONFIGURATION
It is recommended that Schottky diodes be placed in series with
Schottky diode configuration. BAT43 Schottky diodes are used.
AD73271
V+
3V/5V
VDD
VCC
SCLK
VIN0
VIN1
VIN2
VIN3
VIN4
VIN5
VIN6
VIN7
DIN
DOUT
CS
1ADDITIONAL PINS OMITTED FOR CLARITY. 05401-
056
V–
VSS
Figure 56. Schottky Diode Connection
In an application where non-symmetrical VDD and VSS supplies
are being used, adhere to the following guidelines. Table 16
outlines the VSS supply range that can be used for particular
VDD voltages when non-symmetrical supplies are required.
is recommended that these supplies be symmetrical.
Table 16. Non-Symmetrical VDD and VSS Requirements
VDD
Typical VSS Range
5 V
5 V to 5.5 V
6 V
5 V to 8.5 V
7 V
5 V to 11.5 V
8 V
5 V to 15 V
9 V
5 V to 16.5 V
10 V to 16.5 V
5 V to 16.5 V
For the 0 to 4 × VREF range, VSS can be tied to AGND as per
minimum supply recommendations outlined in Table 6.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7709ARUZ-REEL7 | IC ADC 16BIT SIGMA-DELTA 24TSSOP |
| VE-230-IU-S | CONVERTER MOD DC/DC 5V 200W |
| VI-B3F-IW-B1 | CONVERTER MOD DC/DC 72V 100W |
| VI-25Z-MV-S | CONVERTER MOD DC/DC 2V 60W |
| AD7825BRUZ-REEL7 | IC ADC 8BIT 4CH 2MSPS 24-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7327BRUZ-REEL7 | 功能描述:IC ADC 12BIT+ SAR 8CHAN 20TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7328 | 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Channel, Software-Selectable True Bipolar Input, 12-Bit Plus Sign ADC |
| AD7328BRUZ | 功能描述:IC ADC 12BIT+ SAR 8CHAN 20TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:iCMOS® 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7328BRUZ | 制造商:Analog Devices 功能描述:A/D Converter (A-D) IC |
| AD7328BRUZ-REEL | 功能描述:IC ADC 12BIT+SAR 8CHAN 20-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:iCMOS® 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發(fā)布緊急采購，3分鐘左右您將得到回復。