- 您現在的位置：買賣IC網 > PDF目錄8960 > AD7568BSZ (Analog Devices Inc)IC DAC 12BIT OCTAL LC2MOS 44MQFP PDF資料下載
參數資料
| 型號： | AD7568BSZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 2/14頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 12BIT OCTAL LC2MOS 44MQFP |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 標準包裝： | 1 |
| 設置時間： | 500ns |
| 位數： | 12 |
| 數據接口： | 串行 |
| 轉換器數目： | 8 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 17.5mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-QFP |
| 供應商設備封裝： | 44-MQFP（10x10） |
| 包裝： | 托盤 |
| 輸出數目和類型： | 16 電流，單極；16 電流，雙極 |
| 采樣率（每秒）： | 2M |
| 產品目錄頁面： | 785 (CN2011-ZH PDF) |
AD7568
–10–
In the circuit of Figure 19:
C1 = C2, R7 = R8, R3 = R4 (i.e., the same code is loaded to
each DAC).
Resonant frequency, f0 = 1/(2
πR3C1).
Quality Factor, Q = (R6/R8)(R2/R5).
Bandpass Gain, A0 = –R2/R1.
Using the values shown in Figure 19, the Q range is 0.3 to 5,
and the f0 range is 0 to 12 kHz.
APPLICATION HINTS
Output Offset
CMOS D/A converters in circuits such as Figures 15, 16 and 17
exhibit a code dependent output resistance which in turn can
cause a code dependent error voltage at the output of the ampli-
fier. The maximum amplitude of this error, which adds to the
D/A converter nonlinearity, depends on VOS, where VOS is the
amplifier input offset voltage. For the AD7568 to maintain
specified accuracy with VREF at 10 V, it is recommended that
VOS be no greater than 500
V, or (50
10
–6)(V
REF), over the
temperature range of operation. Suitable amplifiers include the
AD OP07, AD OP27, OP177, AD711, AD845 or multiple ver-
sions of these.
Temperature Coefficients
The gain temperature coefficient of the AD7568 has a maxi-
mum value of 5 ppm/
°C and a typical value of 2 ppm/°C. This
corresponds to gain shifts of 2 LSBs and 0.8 LSBs respectively
over a 100
°C temperature range. When trim resistors R1 and
R2 are used to adjust full-scale in Figures 15 and 16, their tem-
perature coefficients should be taken into account. For further
information see “Gain Error and Gain Temperature Coefficient
of CMOS Multiplying DACs,” Application Note, Publication
Number E630c–5–3/86, available from Analog Devices.
High Frequency Considerations
The output capacitances of the AD7568 DACs work in con-
junction with the amplifier feedback resistance to add a pole to
the open loop response. This can cause ringing or oscillation.
Stability can be restored by adding a phase compensation ca-
pacitor in parallel with the feedback resistor. This is shown as
C1 in Figures 15, 16 and 17.
MICROPROCESSOR INTERFACING
AD7568–80C51 Interface
A serial interface between the AD7568 and the 80C51 micro-
controller is shown in Figure 20. TXD of the 80C51 drives
SCLK of the AD7568 while RXD drives the serial data line of
the part. The FSIN signal is derived from the port line P3.3.
The 80C51 provides the LSB of its SBUF register as the first bit
in the serial data stream. Therefore, the user will have to ensure
that the data in the SBUF register is arranged correctly so that
the data word transmitted to the AD7568 corresponds to the
loading sequence shown in Table I. When data is to be trans-
mitted to the part, P3.3 is taken low. Data on RXD is valid on
the falling edge of TXD. The 80C51 transmits its serial data in
8-bit bytes with only eight falling clock edges occurring in the
transmit cycle. To load data to the AD7568, P3.3 is left low af-
ter the first eight bits are transferred, and a second byte of data
is then transferred serially to the AD7568. When the second se-
rial transfer is complete, the P3.3 line is taken high. Note that
the 80C51 outputs the serial data byte in a format which has the
LSB first. The AD7568 expects the MSB first. The 80C51
transmit routine should take this into account.
P3.5
P3.4
P3.3
TXD
RXD
SCLK
SDIN
CLR
LDAC
FSIN
80C51*
AD7568*
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 20. AD7568 to 80C51 Interface
LDAC
and CLR on the AD7568 are also controlled by 80C51
port outputs. The user can bring LDAC low after every two
bytes have been transmitted to update the DAC which has been
programmed. Alternatively, it is possible to wait until all the in-
put registers have been loaded (sixteen byte transmits) and then
update the DAC outputs.
AD7568–68HC11 Interface
Figure 21 shows a serial interface between the AD7568 and the
68HC11 microcontroller. SCK of the 68HC11 drives SCLK of
the AD7568, while the MOSI output drives the serial data line
of the AD7568. The FSIN signal is derived from a port line
(PC7 shown).
For correct operation of this interface, the 68HC11 should be
configured such that its CPOL bit is a 0 and its CPHA bit is a 1.
When data is to be transmitted to the part, PC7 is taken low.
When the 68HC11 is configured like this, data on MOSI is valid
on the falling edge of SCK. The 68HC11 transmits its serial
data in 8-bit bytes (MSB first), with only eight falling clock
edges occurring in the transmit cycle. To load data to the
AD7568, PC7 is left low after the first eight bits are transferred,
and a second byte of data is then transferred serially to the
AD7568. When the second serial transfer is complete, the PC7
line is taken high.
REV. C
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B4Z-MU-F2 | CONVERTER MOD DC/DC 2V 80W |
| D38999/20KG41PB | CONN RCPT 41POS WALL MNT W/PINS |
| VI-B4Y-MU-F4 | CONVERTER MOD DC/DC 3.3V 132W |
| VE-2TH-MY-F4 | CONVERTER MOD DC/DC 52V 50W |
| VI-B4Y-MU-F3 | CONVERTER MOD DC/DC 3.3V 132W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7568BSZ-REEL | 功能描述:IC DAC 12BIT OCTAL LC2MOS 44MQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k |
| AD7569ACHIPS | 功能描述:Analog I/O Interface Die 制造商:analog devices inc. 系列:LC2MOS 包裝:- 零件狀態:上次購買時間 應用:模擬 I/O 接口:總線 電壓 - 電源:4.75 V ~ 5.25 V 封裝/外殼:- 供應商器件封裝:模具 安裝類型:表面貼裝 標準包裝:1 |
| AD7569AQ | 功能描述:IC I/O PORT 8BIT ANLG 24-CDIP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:LC²MOS 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD7569BN | 制造商:Analog Devices 功能描述:Data Acquisition System Single ADC Single DAC 8-Bit 24-Pin PDIP 制造商:Rochester Electronics LLC 功能描述:8-BIT CMOS I/O PORT IC - Bulk |
| AD7569BNZ | 功能描述:IC I/O PORT 8BIT ANALOG 24DIP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:LC²MOS 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
發布緊急采購，3分鐘左右您將得到回復。