參數資料
型號： AD7641ACPRL
廠商： ANALOG DEVICES INC
元件分類： ADC
英文描述： ECONOLINE: REC2.2-S_DRW(Z)/H* - 2.2W DIP Package- 1kVDC Isolation- Regulated Output- 4.5-9V, 9-18V, 18-36V, 36-72V Wide Input Range 2 : 1- UL94V-0 Package Material- Continuous Short Circiut Protection- Cost Effective- 100% Burned In- Efficiency to 84%
中文描述： 1-CH 18-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, QCC48
封裝： MO-220-VKKD, LFCSP-48
文件頁數： 8/24頁
文件大?。?/td> 324K
代理商： AD7641ACPRL
AD7641
Preliminary Technical Data
Pin No.
13
Rev. Pr E | Page 8 of 24
Mnemonic
D6 or
EXT/INT
Type
1
DI/O
Description
In all modes except MODE=3, this output is used as Bit 6 of the Parallel Port Data Ouput Bus.
When MODE=3 (serial mode), this input, part of the serial port, is used as a digital select input for
choosing the internal or an external data clock. With EXT/INT tied LOW, the internal clock is selected
on SCLK output. With EXT/INT set to a logic HIGH, output data is synchronized to an external clock
signal connected to the SCLK input.
In all modes except MODE=3, this output is used as Bit 7 of the Parallel Port Data Output Bus.
When MODE=3 (serial mode), this input, part of the serial port, is used to select the active state of the
SYNC signal. When LOW, SYNC is active HIGH. When HIGH, SYNC is active LOW.
In all modes except MODE=3, this output is used as Bit 8 of the Parallel Port Data Output Bus.
When MODE=3 (serial mode), this input, part of the serial port, is used to invert the SCLK signal. It is
active in both master and slave mode.
In all modes except MODE=3, this output is used as Bit 9 of the Parallel Port Data Output Bus.
When MODE=3 (serial mode), this input, part of the serial port, is used as either an external data input
or a read mode selection input depending on the state of EXT/INT.
When EXT/INT is HIGH, RDC/SDIN could be used as a data input to daisy chain the conversion results
from two or more ADCs onto a single SDOUT line. The digital data level on SDIN is output on SDOUT
with a delay of 18 SCLK periods after the initiation of the read sequence.
When EXT/INT is LOW, RDC/SDIN is used to select the read mode. When RDC/SDIN is HIGH, the data is
output on SDOUT during conversion. When RDC/SDIN is LOW, the data can be output SDOUT only
when the conversion is complete.
Input/Output Interface Digital Power Ground.
Input/Output Interface Digital Power. Nominally at the same supply than the supply of the host
interface (2.5 V or 3 V).
Digital Power. Nominally at 2.5 V.
Digital Power Ground.
In all modes except MODE=3, this output is used as Bit 10 of the Parallel Port Data Output Bus.
When MODE=3 (serial mode), this output, part of the serial port, is used as a serial data output
synchronized to SCLK. Conversion results are stored in an on-chip shift register. The AD7641 provides
the conversion result, MSB first, from its internal shift register. The data format is determined by the
logical level of OB/2C.
In serial mode, when EXT/INT is LOW, SDOUT is valid on both edges of SCLK.
In serial mode, when EXT/INT is HIGH:
If INVSCLK is LOW, SDOUT is updated SCLK rising edge and valid on the next falling edge.
If INVSCLK is HIGH, SDOUT is updated on SCLK falling edge and valid on the next rising edge.
In all modes except MODE=3, this putput is used as the Bit 11 of the Parallel Port Data Output Bus.
When MODE=3 (serial mode), this pin, part of the serial port, is used as a serial data clock input or
output, dependent upon the logic state of the EXT/INT pin. The active edge where the data SDOUT is
updated depends upon the logic state of the INVSCLK pin.
In all modes except MODE=3, this output is used as the Bit 12 of the Parallel Port Data Output Bus.
When MODE=3 (serial mode), this output, part of the serial port, is used as a digital output frame
synchronization for use with the internal data clock (EXT/INT = Logic LOW). When a read sequence is
initiated and INVSYNC is LOW, SYNC is driven HIGH and remains HIGH while SDOUT output is valid.
When a read sequence is initiated and INVSYNC is HIGH, SYNC is driven LOW and remains LOW while
SDOUT output is valid.
In all modes except MODE=3, this output is used as the Bit 12 of the Parallel Port Data Output Bus.
In MODE=3 (serial mode) and when EXT/INT is HIGH, this output, part of the serial port, is used as a
incomplete read error flag. In slave mode, when a data read is started and not complete when the
following conversion is complete, the current data is lost and RDERROR is pulsed high.
Bit 14 to Bit 17 of the Parallel Port Data output bus. These pins are always outputs regardless of the
interface mode.
Busy Output. Transitions HIGH when a conversion is started, and remains HIGH until the conversion is
complete and the data is latched into the on-chip shift register.
The falling edge of BUSY could be used as a data ready clock signal.
Must be tied to digital ground.
Read Data. When CS and RD are both LOW, the interface parallel or serial output bus is enabled.
Chip Select. When CS and RD are both LOW, the interface parallel or serial output bus is enabled. CS is
also used to gate the external clock.
14
D7or
INVSYNC
DI/O
15
D8 or
INVSCLK
DI/O
16
D9 or
RDC/SDIN
DI/O
17
18
OGND
OVDD
P
P
19
20
21
DVDD
DGND
D10 or
SDOUT
P
P
DO
22
D11 or
SCLK
DI/O
23
D12 or
SYNC
DO
24
D13 or
RDERROR
DO
25-28
D[14:17]
DO
29
BUSY
DO
30
31
32
DGND
RD
CS
P
DI
DI
相關PDF資料
PDF描述
AD7641AST 18-Bit, 2 MSPS SAR ADC
AD7641ASTRL 18-Bit, 2 MSPS SAR ADC
AD7650 16-Bit 1 MSPS SAR Unipolar ADC with Ref
AD7651 Circular Connector; MIL SPEC:MIL-DTL-38999 Series III; Body Material:Metal; Series:D38999 Series III; No. of Contacts:4; Connector Shell Size:13; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Body Style:Straight RoHS Compliant: No
AD7652 Circular Connector; MIL SPEC:MIL-DTL-38999 Series III; Body Material:Metal; Series:D38999 Series III; No. of Contacts:4; Connector Shell Size:13; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Body Style:Straight RoHS Compliant: No
相關代理商/技術參數
參數描述
AD7641AST 制造商:Analog Devices 功能描述:ADC SGL SAR 2MSPS 18BIT PARALLEL/SERL 48LQFP - Bulk
AD7641ASTRL 制造商:Analog Devices 功能描述:ADC SGL SAR 2MSPS 18BIT PARALLEL/SERL 48LQFP - Tape and Reel
AD7641BCPZ 功能描述:IC ADC 18BIT 2MSPS SAR 48-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD7641BCPZRL 功能描述:IC ADC 18BIT 2MSPS SAR 48-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD7641BSTZ 功能描述:IC ADC 18BIT 2MSPS SAR 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*