- 您現在的位置：買賣IC網 > PDF目錄10248 > AD7650ASTZRL (Analog Devices Inc)IC ADC 16BIT CMOS 5V 48LQFP PDF資料下載
參數資料
| 型號： | AD7650ASTZRL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 19/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT CMOS 5V 48LQFP |
| 標準包裝： | 2,000 |
| 位數： | 16 |
| 采樣率（每秒）： | 570k |
| 數據接口： | 串行，并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 77mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個偽差分，單極 |
| 配用： | EVAL-AD7650CBZ-ND - BOARD EVALUATION FOR AD7650 |
REV. 0
AD7650
–8–
DEFINITION OF SPECIFICATIONS
INTEGRAL NONLINEARITY ERROR (INL)
Linearity error refers to the deviation of each individual code
from a line drawn from “negative full scale” through “positive
full scale.” The point used as “negative full scale” occurs 1/2 LSB
before the first code transition. “Positive full scale” is defined as a
level 1 1/2 LSB beyond the last code transition. The deviation is
measured from the middle of each code to the true straight line.
DIFFERENTIAL NONLINEARITY ERROR (DNL)
In an ideal ADC, code transitions are 1 LSB apart. Differential
nonlinearity is the maximum deviation from this ideal value. It is
often specified in terms of resolution for which no missing codes
are guaranteed.
FULL-SCALE ERROR
The last transition (from 011 . . . 10 to 011 . . . 11 in two’s comple-
ment coding) should occur for an analog voltage 1 1/2 LSB below
the nominal full scale (2.49994278 V for the 0 V–2.5 V range).
The full-scale error is the deviation of the actual level of the last
transition from the ideal level.
UNIPOLAR ZERO ERROR
The first transition should occur at a level 1/2 LSB above analog
ground (19.073
V for the 0 V–2.5 V range). Unipolar zero
error is the deviation of the actual transition from that point.
SPURIOUS FREE DYNAMIC RANGE (SFDR)
The difference, in decibels (dB), between the rms amplitude of
the input signal and the peak spurious signal.
EFFECTIVE NUMBER OF BITS (ENOB)
ENOB is a measurement of the resolution with a sine wave input.
It is related to S/(N+D) by the following formula:
ENOB
S N
D
dB
=+
[]
()
176
6 02
./ .
and is expressed in bits.
TOTAL HARMONIC DISTORTION (THD)
THD is the ratio of the rms sum of the first five harmonic compo-
nents to the rms value of a full-scale input signal and is expressed
in decibels.
SIGNAL-TO-NOISE RATIO (SNR)
SNR is the ratio of the rms value of the actual input signal to the
rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in decibels.
SIGNAL TO (NOISE + DISTORTION) RATIO (S/[N+D])
S/(N+D) is the ratio of the rms value of the actual input signal to
the rms sum of all other spectral components below the Nyquist
frequency, including harmonics but excluding dc. The value for
S/(N+D) is expressed in decibels.
APERTURE DELAY
Aperture delay is a measure of the acquisition performance and
is measured from the falling edge of the
CNVST input to when
the input signal is held for a conversion.
TRANSIENT RESPONSE
The time required for the AD7650 to achieve its rated accuracy
after a full-scale step function is applied to its input.
OVERVOLTAGE RECOVERY
The time required for the ADC to recover to full accuracy after
an analog input signal 150% of full-scale is reduced to 50% of
the full-scale value.
NOTES
AI = Analog Input
DI = Digital Input
DI/O = Bidirectional Digital
DO = Digital Output
P = Power
PIN FUNCTION DESCRIPTIONS (continued)
Pin No.
Mnemonic
Type
Description
35
CNVST
DI
Start Conversion. A falling edge on
CNVST puts the internal sample/hold into the hold state
and initiates a conversion. In impulse mode (IMPULSE HIGH and WARP LOW), if
CNVST
is held low when the acquisition phase (t8) is complete, the internal sample/hold is put into
the hold state and a conversion is immediately started.
36
AGND
P
Must Be Tied to Analog Ground
37
REF
AI
Reference Input Voltage
38
REFGND
AI
Reference Input Analog Ground
39
IN–
AI
Analog Input Ground
43
IN+
AI
Primary Analog Input with a Range of 0 V to VREF.
相關PDF資料 |
PDF描述 |
|---|---|
| 17982-7SG-3ES | CONN RCPT 7POS PNL MNT SKT |
| VE-B60-MY | CONVERTER MOD DC/DC 5V 50W |
| AD7650ACPZRL | IC ADC 16BIT CMOS 5V 48LFCSP |
| VE-B5F-MY | CONVERTER MOD DC/DC 72V 50W |
| VE-B5B-MY | CONVERTER MOD DC/DC 95V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7651 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit 1 MSPS SAR Unipolar ADC with Ref |
| AD7651ACP | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 16-bit Parallel/Serial 48-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:16-BIT 100KSPS SAR UNIPOLAR ADC W/ REF - Bulk 制造商:Analog Devices 功能描述:16BIT SAR ADC REF 7651 LFSCP-48 |
| AD7651ACPRL | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 16-bit Parallel/Serial 48-Pin LFCSP EP T/R |
| AD7651ACPZ | 功能描述:IC ADC 16BIT UNIPOLAR 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7651ACPZRL | 功能描述:IC ADC 16BIT UNIPOLAR 48LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。