- 您現在的位置：買賣IC網 > PDF目錄10138 > AD7678ASTZRL (Analog Devices Inc)IC ADC 18BIT SAR 100KSPS 48-LQFP PDF資料下載
參數資料
| 型號： | AD7678ASTZRL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 18BIT SAR 100KSPS 48-LQFP |
| 標準包裝： | 2,000 |
| 系列： | PulSAR® |
| 位數： | 18 |
| 采樣率（每秒）： | 100k |
| 數據接口： | 串行，并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 26mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，雙極 |
| 配用： | EVAL-AD7678CB-ND - BOARD EVALUATION FOR AD7678 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7678
Rev. A | Page 17 of 28
TYPICAL CONNECTION DIAGRAM
Figure 21 shows a typical connection diagram for the AD7678.
Different circuitry shown on this diagram is optional and is
discussed later in this data sheet.
Analog Inputs
Figure 22 shows a simplified analog input section of the
AD7678. The diodes shown in Figure 22 provide ESD protec-
tion for the inputs. Care must be taken to ensure that the analog
input signal never exceeds the absolute ratings on these inputs.
This will cause these diodes to become forward-biased and start
conducting current. These diodes can handle a forward-biased
current of 120 mA max. This condition could eventually occur
when the input buffer’s U1 or U2 supplies are different from
AVDD. In such a case, an input buffer with a short-circuit
current limitation can be used to protect the part.
IN+
IN–
AGND
AVDD
R+ = 3k
CS
R– = 3k
03084-0-028
Figure 22. Simplified Analog Input
This analog input structure is a true differential structure. By
using these differential inputs, signals common to both inputs
are rejected as shown in Figure 23, which represents typical
CMRR over frequency.
FREQUECY (kHz)
80
CMRR
(dB)
75
50
100
1000
10000
110
70
65
60
55
03084-0-029
Figure 23. Analog Input CMRR vs. Frequency
During the acquisition phase for ac signals, the AD7678 behaves
like a 1-pole RC filter consisting of the equivalent resistance,
R+, R–, and CS. Resistors R+ and R– are typically 3 k and are
lumped components made up of a serial resistor and the on
resistance of the switches. CS is typically 60 pF and mainly
consists of the ADC sampling capacitor. This 1-pole filter with a
–3 dB cutoff frequency of 900 kHz typ reduces any undesirable
aliasing effect and limits the noise coming from the inputs.
Because the input impedance of the AD7678 is very high, the
part can be driven directly by a low impedance source without
gain error.
Driver Amplifier Choice
Although the AD7678 is easy to drive, the driver amplifier
needs to meet the following requirements:
The driver amplifier and the AD7678 analog input circuit
have to be able to settle for a full-scale step of the capacitor
array at an 18-bit level (0.0004%). In the amplifier’s data
sheet, settling at 0.1% or 0.01% is more commonly
specified. This could differ significantly from the settling
time at an 18-bit level and, therefore, should be verified
prior to driver selection. The tiny op amp AD8021, which
combines ultralow noise and high gain-bandwidth, meets
this settling time requirement.
The noise generated by the driver amplifier needs to be
kept as low as possible in order to preserve the SNR and
transition noise performance of the AD7678. The noise
coming from the driver is filtered by the AD7678 analog
input circuit 1-pole low-pass filter made by R+, R–, and CS.
The SNR degradation due to the amplifier is
2
)
(
625
25
log
20
N
3dB
–
LOSS
Ne
f
SNR
where:
f–3dB
is the –3 dB input bandwidth in MHz of the AD7678
(0.9 MHz).
N
is the noise factor of the amplifiers (1 if in buffer
configuration).
eN
is the equivalent input noise voltage of each op amp in
nV/Hz.
For instance, for a driver with an equivalent input noise of
6 nV/Hz (e.g., AD8610) configured as a buffer, thus with
a noise gain of +1, the SNR degrades by only 0.65 dB.
The driver needs to have a THD performance suitable to
that of the AD7678.
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/20WD19SA | CONN RCPT 19POS WALL MNT W/SCKT |
| AD7712ARZ-REEL7 | IC ADC 24BIT SGNL CONDTNR 24SOIC |
| MS3100E12S-3SW | CONN RCPT 2POS WALL MNT W/SCKT |
| IDT72V01L25JI8 | IC ASYNCH 512X9 25NS 32-PLCC |
| IDT7201LA15JI8 | IC MEM FIFO 512X9 15NS 32-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7679 | 制造商:AD 制造商全稱:Analog Devices 功能描述:18-Bit, 2.5 LSB INL, 570 kSPS SAR ADC |
| AD7679ACP | 制造商:Analog Devices 功能描述:ADC Single SAR 570ksps 18-bit Parallel/Serial 48-Pin LFCSP EP 制造商:Analog Devices 功能描述:18BIT SAR ADC SMD 7679 LFSCP-48 |
| AD7679ACPRL | 制造商:Analog Devices 功能描述:ADC Single SAR 570ksps 18-bit Parallel/Serial 48-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 570KSPS 18BIT PARALLEL/SERL 48LFCSP EP - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:18-BIT,100KSPSSARADC - Tape and Reel |
| AD7679ACPZ | 功能描述:IC ADC 18BIT SAR W/BUFF 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7679ACPZRL | 功能描述:IC ADC 18BIT SAR W/BUFF 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。