- 您現在的位置：買賣IC網 > PDF目錄10138 > AD7679ACPZRL (Analog Devices Inc)IC ADC 18BIT SAR W/BUFF 48LFCSP PDF資料下載
參數資料
| 型號： | AD7679ACPZRL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 18BIT SAR W/BUFF 48LFCSP |
| 標準包裝： | 2,500 |
| 系列： | PulSAR® |
| 位數： | 18 |
| 采樣率（每秒）： | 570k |
| 數據接口： | 串行，并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 103mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 48-LFCSP-VQ（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，雙極 |
| 配用： | EVAL-AD7679CBZ-ND - BOARD EVALUATION FOR AD7679 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7679
Rev. A | Page 18 of 28
The SNR degradation due to the amplifier is
=
π
+
2
)
(
625
25
log
20
N
3dB
–
LOSS
Ne
f
SNR
where:
f–3dB is the –3 dB input bandwidth in MHz of the AD7679
(26 MHz) or the cutoff frequency of the input filter, if used.
N is the noise factor of the amplifiers (1 if in buffer
configuration).
eN is the equivalent input noise voltage of each op amp in
nV/√Hz.
For instance, for a driver with an equivalent input noise of
2 nV/√Hz (e.g., AD8021) configured as a buffer, thus with
a noise gain of +1, the SNR degrades by only 0.34 dB with
the filter in Figure 25, and by 1.8 dB without it.
The driver needs to have a THD performance suitable to
that of the AD7679.
The AD8021 meets these requirements and is usually
appropriate for almost all applications. The AD8021 needs a
10 pF external compensation capacitor, which should have good
linearity as an NPO ceramic or mica type.
The AD8022 could be used if a dual version is needed and gain
of 1 is present. The AD829 is an alternative in applications
where high frequency (above 100 kHz) performance is not
required. In gain of 1 applications, it requires an 82 pF
compensation capacitor. The AD8610 is another option when
low bias current is needed in low frequency applications.
Single-to-Differential Driver
For applications using unipolar analog signals, a single-ended-
to-differential driver will allow for a differential input into the
part. The schematic is shown in Figure 29. When provided an
input signal of 0 to VREF, this configuration will produce a
differential ±VREF with midscale at VREF/2.
If the application can tolerate more noise, the AD8138,
differential driver can be used.
U2
8.25k
Ω
2.5V
AD8021
590
Ω
AD7679
IN+
IN– REF
U1
ANALOG INPUT
(UNIPOLAR
0V TO 4.096V)
10pF
AD8021
590
Ω
10pF
10
μF
100nF
1.82k
Ω
2.7nF
30
Ω
2.7nF
30
Ω
REFBUFIN
03085-0-031
Figure 29. Single-Ended-to-Differential Driver Circuit
(Internal Reference Buffer Used)
Voltage Reference
The AD7679 allows the use of an external voltage reference
either with or without the internal reference buffer.
Using the internal reference buffer is recommended when
sharing a common reference voltage between multiple ADCs is
desired.
However, the advantages of using the external reference voltage
directly are
The SNR and dynamic range improvement (about 1.7 dB)
resulting from the use of a reference voltage very close to
the supply (5 V) instead of a typical 4.096 V reference
when the internal buffer is used.
The power saving when the internal reference buffer is
powered down (PDBUF high).
To use the internal reference buffer, PDBUF should be LOW. A
2.5 V reference voltage applied on the REFBUFIN input will
result in a 4.096 V reference on the REF pin.
In both cases, the voltage reference input REF has a dynamic
input impedance and therefore requires an efficient decoupling
between REF and REFGND inputs. The decoupling consists of
a low ESR 47 μF tantalum capacitor connected to the REF and
REFGND inputs with minimum parasitic inductance.
Care should also be taken with the reference temperature
coefficient of the voltage reference, which directly affects the
full-scale accuracy if this parameter matters. For instance, a
±4 ppm/°C temperature coefficient of the reference changes the
full scale by ±1 LSB/°C.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-221-IW-F1 | CONVERTER MOD DC/DC 12V 100W |
| VE-24N-IU-F2 | CONVERTER MOD DC/DC 18.5V 200W |
| VE-B3Z-IV-B1 | CONVERTER MOD DC/DC 2V 60W |
| MS3101A20-3P | CONN RCPT 3POS FREE HNG W/PINS |
| MS3102A36-1P | CONN RCPT 22POS BOX MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7679AST | 制造商:Analog Devices 功能描述:ADC Single SAR 570ksps 18-bit Parallel/Serial 48-Pin LQFP 制造商:Analog Devices 功能描述:18BIT SAR ADC SMD 7679 LQFP48 |
| AD7679ASTRL | 制造商:Analog Devices 功能描述:ADC Single SAR 570ksps 18-bit Parallel/Serial 48-Pin LQFP T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 570KSPS 18BIT PARALLEL/SERL 48LQFP - Tape and Reel |
| AD7679ASTZ | 功能描述:IC ADC 18BIT 570KSPS 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7679ASTZ | 制造商:Analog Devices 功能描述:IC 18-BIT ADC |
| AD7679ASTZRL | 功能描述:IC ADC 18BIT SAR W/BUFF 48LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。