- 您現在的位置：買賣IC網 > PDF目錄10117 > AD7711AR-REEL7 (Analog Devices Inc)IC ADC 24BIT RTD I SOURCE 24SOIC PDF資料下載
參數資料
| 型號： | AD7711AR-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 24BIT RTD I SOURCE 24SOIC |
| 標準包裝： | 400 |
| 位數： | 24 |
| 采樣率（每秒）： | 1.03k |
| 數據接口： | 串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 52.5mW |
| 電壓電源： | 模擬和數字，雙 ± |
| 工作溫度： | -40°C ~ 80°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 24-SOIC W |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個單端，單極；1 個單端，雙極；1 個差分，單極；1 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
2
REV.G
AD7711
–19–
Measurement errors due to offset drift or gain drift can be elimi-
nated at any time by recalibrating the converter or by operating
the part in the background calibration mode. Using the system
calibration mode can also minimize offset and gain errors in the
signal conditioning circuitry. Integral and differential linearity
errors are not significantly affected by temperature changes.
POWER SUPPLIES AND GROUNDING
Because the analog inputs and reference input are differential,
most of the voltages in the analog modulator are common-mode
voltages. VBIAS provides the return path for most of the analog
currents flowing in the analog modulator. As a result, the VBIAS
input should be driven from a low impedance to minimize errors
due to charging/discharging impedances on this line. When the
internal reference is used as the reference source for the part,
AGND is the ground return for this reference voltage.
The analog and digital supplies to the AD7711 are independent
and separately pinned out to minimize coupling between the
analog and digital sections of the device. The digital filter will
provide rejection of broadband noise on the power supplies,
except at integer multiples of the modulator sampling frequency.
The digital supply (DVDD) must not exceed the analog positive
supply (AVDD) by more than 0.3 V in normal operation. If separate
analog and digital supplies are used, the recommended decoupling
scheme is shown in Figure 9. In systems where AVDD = 5 V and
DVDD = 5 V, it is recommended that AVDD and DVDD are
driven from the same 5 V supply, although each supply should be
decoupled separately as shown in Figure 9. It is preferable that
the common supply is the system’s analog 5 V supply.
It is also important that power is applied to the AD7711 before
signals at REF IN, AIN, or the logic input pins in order to avoid
latch-up. If separate supplies are used for the AD7711 and the
system digital circuitry, the AD7711 should be powered up first.
If it is not possible to guarantee this, current limiting resistors
should be placed in series with the logic inputs.
AD7711
AVDD
DVDD
0.1 F
10 F
ANALOG
SUPPLY
0.1 F
DIGITAL 5V
SUPPLY
Figure 9. Recommended Decoupling Scheme
DIGITAL INTERFACE
The AD7711’s serial communications port provides a flexible
arrangement to allow easy interfacing to industry-standard
microprocessors, microcontrollers, and digital signal processors.
A serial read to the AD7711 can access data from the output
register, the control register, or the calibration registers. A serial
write to the AD7711 can write data to the control register or the
calibration registers.
Two different modes of operation are available, optimized for
different types of interfaces where the AD7711 can act either as
master in the system (it provides the serial clock) or as slave (an
external serial clock can be provided to the AD7711). These
two modes, labelled self-clocking mode and external clocking
mode, are discussed in detail in the following sections.
相關PDF資料 |
PDF描述 |
|---|---|
| MS3106R18-11PX | CONN PLUG 5POS STRAIGHT W/PINS |
| MS3101F14S-9P | CONN RCPT 2POS FREE HNG W/PINS |
| LTC1609AISW | IC ADC SRL 16BIT 200KSPS 20-SOIC |
| LTC1383CN#PBF | IC TXRX 5V RS232 LOW PWR 16-DIP |
| MS3101E14S-9P | CONN RCPT 2POS FREE HNG W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7711ARZ | 功能描述:IC ADC 24BIT RTD I SOURCE 24SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7711ARZ | 制造商:Analog Devices 功能描述:LC 2MOS SIGNAL CONDITIONING ANALOG/DIGIT |
| AD7711ARZ-REEL | 功能描述:IC ADC 24BIT RTD I SOURCE 24SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7711ARZ-REEL7 | 功能描述:IC ADC 24BIT RTD I SOURCE 24SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7711ASQ | 功能描述:模數轉換器 - ADC CMOS 24B w/ Matched RTD Excitation Crnt RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
發布緊急采購，3分鐘左右您將得到回復。