- 您現在的位置：買賣IC網 > PDF目錄10090 > AD7711AR (Analog Devices Inc)IC ADC 24BIT RTD I SOURCE 24SOIC PDF資料下載
參數資料
| 型號： | AD7711AR |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 26/28頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT RTD I SOURCE 24SOIC |
| 標準包裝： | 1 |
| 位數： | 24 |
| 采樣率（每秒）： | 1.03k |
| 數據接口： | 串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 52.5mW |
| 電壓電源： | 模擬和數字，雙 ± |
| 工作溫度： | -40°C ~ 80°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 24-SOIC W |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個單端，單極；1 個單端，雙極；1 個差分，單極；1 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁
2
REV.G
AD7711
–7–
PIN FUNCTION DESCRIPTIONS
Pin
Mnemonic
Function
1
SCLK
Serial Clock. Logic input/output, depending on the status of the MODE pin. When MODE is high, the
device is in its self-clocking mode, and the SCLK pin provides a serial clock output. This SCLK becomes
active when
RFS or TFS goes low, and goes high impedance when either RFS or TFS returns high or when
the device has completed transmission of an output word. When MODE is low, the device is in its external
clocking mode and the SCLK pin acts as an input. This input serial clock can be a continuous clock with all
data transmitted in a continuous train of pulses. Alternatively, it can be a noncontinuous clock with the
information being transmitted to the AD7711 in smaller batches of data.
2
MCLK IN
Master Clock Signal for the Device. This can be provided in the form of a crystal or external clock. A crystal can
be tied across the MCLK IN and MCLK OUT pins. Alternatively, the MCLK IN pin can be driven with a
CMOS-compatible clock and MCLK OUT left unconnected. The clock input frequency is nominally 10 MHz.
3
MCLK OUT
When the master clock for the device is a crystal, the crystal is connected between MCLK IN and MCLK OUT.
4A0Address Input. With this input low, reading and writing to the device is to the control register. With this input
high, access is to either the data register or the calibration registers.
5
SYNC
Logic Input. Allows for synchronization of the digital filters when using a number of AD7711s. It resets
the nodes of the digital filter.
6
MODE
Logic Input. When this pin is high, the device is in its self-clocking mode; with this pin low, the device is in its
external clocking mode.
7
AIN1(+)
Analog Input Channel 1. Positive input of the programmable gain differential analog input. The AIN1(+) input
is connected to an output current source that can be used to check that an external transducer has burned out
or gone open circuit. This output current source can be turned on/off via the control register.
8
AIN1(–)
Analog Input Channel 1. Negative input of the programmable gain differential analog input.
9
RTD1
Constant Current Output. A nominal 200
mA constant current is provided at this pin; this current can be
used as the excitation current for RTDs. This current can be turned on or off via the control register.
10
RTD2
Constant Current Output. A nominal 200
mA constant current is provided at this pin; this current can be
used as the excitation current for RTDs. This current can be turned on or off via the control register, and
can be used to eliminate lead resistance errors in 3-wire RTD configurations.
11
VSS
Analog Negative Supply, 0 V to –5 V. Tied to AGND for single-supply operation. The input voltage on AIN1
or AIN2 should not go > 30 mV negative w.r.t. VSS for correct operation of the device.
12
AVDD
Analog Positive Supply Voltage, 5 V to 10 V.
13
VBIAS
Input Bias Voltage. This input voltage should be set such that VBIAS + 0.85
VREF < AVDD and VBIAS – 0.85
VREF > VSS where VREF is REF IN(+) – REF IN(–). Ideally, this should be tied halfway between AVDD
and VSS. Thus with AVDD = 5 V and VSS = 0 V, it can be tied to REF OUT; with AVDD = +5 V and
VSS = –5 V, it can be tied to AGND; with AVDD = 10 V, it can be tied to 5 V.
14
REF IN(–)
Reference Input. The REF IN(–) can lie anywhere between AVDD and VSS provided REF IN(+) is greater
than REF IN(–).
15
REF IN(+)
Reference Input. The reference input is differential provided REF IN(+) is greater than REF IN(–).
REF IN(+) can lie anywhere between AVDD and VSS.
16
REF OUT
Reference Output. The internal 2.5 V reference is provided at this pin. This is a single-ended output
that is referred to AGND. It is a buffered output capable of providing 1 mA to an external load.
17
AIN2
Analog Input Channel 2. Single-ended programmable gain analog input.
18
AGND
Ground Reference Point for Analog Circuitry.
19
TFS
Transmit Frame Synchronization. Active low logic input used to write serial data to the device with serial
data expected after the falling edge of this pulse. In the self-clocking mode, the serial clock becomes active
after
TFS goes low. During a write operation to the AD7711, the SDATA line should not return to high
impedance until after
TFS returns high.
相關PDF資料 |
PDF描述 |
|---|---|
| MS3106R16-11S | CONN PLUG 2POS STRAIGHT W/SCKT |
| VI-B3F-IV-F2 | CONVERTER MOD DC/DC 72V 150W |
| VI-B3F-IV-F1 | CONVERTER MOD DC/DC 72V 150W |
| MS3102E16-2P | CONN RCPT 1POS BOX MNT W/PINS |
| VI-B3D-IV-F4 | CONVERTER MOD DC/DC 85V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7711AR-REEL | 功能描述:IC ADC 24BIT RTD I SOURCE 24SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7711AR-REEL7 | 功能描述:IC ADC 24BIT RTD I SOURCE 24SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7711ARZ | 功能描述:IC ADC 24BIT RTD I SOURCE 24SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7711ARZ | 制造商:Analog Devices 功能描述:LC 2MOS SIGNAL CONDITIONING ANALOG/DIGIT |
| AD7711ARZ-REEL | 功能描述:IC ADC 24BIT RTD I SOURCE 24SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。