- 您現在的位置：買賣IC網 > PDF目錄10239 > AD7714YRUZ-REEL7 (Analog Devices Inc)IC ADC 24BIT SIGMA-DELTA 24TSSOP PDF資料下載
參數資料
| 型號： | AD7714YRUZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 2/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 24BIT SIGMA-DELTA 24TSSOP |
| 標準包裝： | 1,000 |
| 位數： | 24 |
| 采樣率（每秒）： | 1k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 7mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 24-TSSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 3 個差分，單極；3 個差分，雙極；5 個偽差分，單極；5 個偽差分，雙極 |
| 配用： | EVAL-AD7714-3EBZ-ND - BOARD EVAL FOR AD7714 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
AD7714
REV. C
–10–
PIN FUNCTION DESCRIPTION (Continued)
Pin
No. Mnemonic
Function
19
CS
Chip Select. Active low Logic Input used to select the AD7714. With this input hard-wired low, the AD7714
can operate in its three-wire interface mode with SCLK, DIN and DOUT used to interface to the device.
CS
can be used to select the device in systems with more than one device on the serial bus or as a frame
synchronization signal in communicating with the AD7714.
20
DRDY
Logic output. A logic low on this output indicates that a new output word is available from the AD7714 data
register. The
DRDY pin will return high upon completion of a read operation of a full output word. If no data
read has taken place, after an output update, the
DRDY line will return high for 500
× t
CLK IN cycles prior to
the next output update. This gives an indication of when a read operation should not be attempted to avoid
reading from the data register as it is being updated.
DRDY is also used to indicate when the AD7714 has
completed its on-chip calibration sequence.
21
DOUT
Serial Data Output with serial data being read from the output shift register on the part. This output shift
register can contain information from the calibration registers, mode register, communications register, filter
selection registers or data register depending on the register selection bits of the Communications Register.
22
DIN
Serial Data Input with serial data being written to the input shift register on the part. Data from this input shift
register is transferred to the calibration registers, mode register, communications register or filter selection
registers depending on the register selection bits of the Communications Register.
23
DVDD
Digital Supply Voltage, A Grade Versions: +3.3 V or +5 V nominal; Y Grade Versions: 3 V or 5 V nominal.
24
DGND
Ground reference point for digital circuitry.
BIPOLAR NEGATIVE FULL-SCALE ERROR
This is the deviation of the first code transition from the ideal
AIN(+) voltage (AIN(–) – VREF/GAIN + 0.5 LSB) when operat-
ing in the bipolar mode.
POSITIVE FULL-SCALE OVERRANGE
Positive Full-Scale Overrange is the amount of overhead avail-
able to handle input voltages on AIN(+) input greater than
AIN(–) + VREF/GAIN (for example, noise peaks or excess volt-
ages due to system gain errors in system calibration routines)
without introducing errors due to overloading the analog modu-
lator or overflowing the digital filter.
NEGATIVE FULL-SCALE OVERRANGE
This is the amount of overhead available to handle voltages on
AIN(+) below AIN(–) – VREF/GAIN without overloading the
analog modulator or overflowing the digital filter. Note that the
analog input will accept negative voltage peaks even in the uni-
polar mode provided that AIN(+) is greater than AIN(–) and
greater than AGND – 30 mV.
OFFSET CALIBRATION RANGE
In the system calibration modes, the AD7714 calibrates its
offset with respect to the analog input. The Offset Calibration
Range specification defines the range of voltages that the
AD7714 can accept and still calibrate offset accurately.
FULL-SCALE CALIBRATION RANGE
This is the range of voltages that the AD7714 can accept in the
system calibration mode and still calibrate full scale correctly.
INPUT SPAN
In system calibration schemes, two voltages applied in sequence
to the AD7714’s analog input define the analog input range.
The input span specification defines the minimum and maxi-
mum input voltages from zero to full scale that the AD7714 can
accept and still calibrate gain accurately.
TERMINOLOGY*
INTEGRAL NONLINEARITY
This is the maximum deviation of any code from a straight line
passing through the endpoints of the transfer function. The end-
points of the transfer function are zero scale (not to be confused
with bipolar zero), a point 0.5 LSB below the first code transi-
tion (000 . . . 000 to 000 . . . 001) and full scale, a point
0.5 LSB above the last code transition (111 . . . 110 to
111 . . . 111). The error is expressed as a percentage of full
scale.
POSITIVE FULL-SCALE ERROR
Positive Full-Scale Error is the deviation of the last code transi-
tion (111 . . . 110 to 111 . . . 111) from the ideal AIN(+) voltage
(AIN(–) + VREF/GAIN – 3/2 LSBs). It applies to both unipolar
and bipolar analog input ranges.
UNIPOLAR OFFSET ERROR
Unipolar Offset Error is the deviation of the first code transition
from the ideal AIN(+) voltage (AIN(–) + 0.5 LSB) when oper-
ating in the unipolar mode.
BIPOLAR ZERO ERROR
This is the deviation of the midscale transition (0111 . . . 111
to 1000 . . . 000) from the ideal AIN(+) voltage (AIN(–) –
0.5 LSB) when operating in the bipolar mode.
GAIN ERROR
This is a measure of the span error of the ADC. It includes full-
scale errors but not zero-scale errors. For unipolar input ranges
it is defined as (full-scale error – unipolar offset error) while for
bipolar input ranges it is defined as (full-scale error – bipolar
zero error).
*AIN(–) refers to the negative input of the differential input pairs or to AIN6
when referring to the pseudo-differential input configurations.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B2W-MW-F1 | CONVERTER MOD DC/DC 5.5V 100W |
| VI-23B-CU-F4 | CONVERTER MOD DC/DC 95V 200W |
| AD7714YRZ-REEL | IC ADC 24BIT SIGMA-DELTA 24SOIC |
| VI-23B-CU-F3 | CONVERTER MOD DC/DC 95V 200W |
| VI-B7Z-MW | CONVERTER MOD DC/DC 2V 40W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7714YRZ | 功能描述:IC ADC 24BIT SIGMA-DELTA 24SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7714YRZ | 制造商:Analog Devices 功能描述:IC ADC 24-BIT SIGMA DELTA |
| AD7714YRZ-REEL | 功能描述:IC ADC 24BIT SIGMA-DELTA 24SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7714YRZ-REEL7 | 功能描述:IC ADC 24BIT SIGMA-DELTA 24SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7715 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V/5 V, 450 uA 16-Bit, Sigma-Delta ADC |
發布緊急采購，3分鐘左右您將得到回復。