參數資料
型號： AD7732BRUZ-REEL7
廠商： Analog Devices Inc
文件頁數： 24/32頁
文件大?。?/td> 0K
描述： IC ADC 24BIT 2CH SIG-DEL 28TSSOP
標準包裝： 1,000
位數： 24
采樣率（每秒）： 15.4k
數據接口： DSP，MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 1
功率耗散（最大）： 100mW
電壓電源： 模擬和數字
工作溫度： -40°C ~ 105°C
安裝類型： 表面貼裝
封裝/外殼： 28-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 28-TSSOP
包裝： 帶卷 (TR)
輸入數目和類型： 2 個差分，單極；2 個差分，雙極
配用： EVAL-AD7732EBZ-ND - BOARD EVAL FOR AD7732
AD7732
Rev. A | Page 30 of 32
I/O Port
The AD7732 P0 pin can be used as a general-purpose digital
I/O pin. The P1 pin (SYNC/P1) can be used as a general-
purpose digital I/O pin or to synchronize the AD7732 with
other devices in the system. When the SYNC bit in the I/O port
register is set and the SYNC pin is low, the AD7732 does not
process any conversion. If it is put into single conversion mode,
continuous conversion mode, or any calibration mode, the
AD7732 waits until the SYNC pin goes high and then starts
operation. This allows conversion to start from a known point
in time, i.e., the rising edge of the SYNC pin.
The digital P0 and P1 voltage is referenced to the analog
supplies. When configured as inputs, the pins should be tied
high or low.
Calibration
The AD7732 provides zero-scale self-calibration and zero- and
full-scale system calibration capability that can effectively
reduce the offset error and gain error to the order of the noise.
After each conversion, the ADC conversion result is scaled
using the ADC calibration registers and the relevant channel
calibration registers before being written to the data register.
For unipolar ranges:
Data = ((ADC result – ADC ZS Cal. reg.)
× ADC FS Reg./200000h – Ch. ZS Cal. reg.)
× Ch. FS Cal. reg./200000h
For bipolar ranges:
Data = ((ADC result – ADC ZS Cal. reg.)
× ADC FS Reg./400000h + 800000h – Ch. ZS Cal.
reg.)
× Ch. FS Cal. reg./200000h
Where the ADC result is in the range of 0 to FFFFFFh.
Note that the channel zero-scale calibration register has the
format of a sign bit and a 22-bit channel offset value. It is
strongly recommended that the user not change the ADC full-
scale register.
To start any calibration, write the relevant mode bits to the
AD7732 mode register. After the calibration is complete, the
contents of the corresponding calibration registers are updated,
all RDY bits in the ADC status register are set, the RDY pin
goes low, and the AD7732 reverts to idle mode. The calibration
duration is the same as the conversion time configured on the
selected channel. A longer conversion time gives less noise and
yields a more exact calibration; therefore, use at least the default
conversion time to initiate any calibration.
ADC Zero-Scale Self-Calibration
The ADC zero-scale self-calibration can reduce the offset error
in the chopping disabled mode. If repeated after a temperature
change, it can also reduce the offset drift error in the chopping
disabled mode.
The zero-scale self-calibration is performed on internally
shorted ADC inputs. The negative analog input terminal on the
selected channel is used to set the ADC zero-scale calibration
common mode. Therefore, either the negative terminal of the
selected differential pair or the AINCOM on the single-ended
channel configuration should be driven to a proper common-
mode voltage.
It is strongly recommended that the ADC zero-scale calibration
register should only be updated as part of a zero-scale self-
calibration.
Per Channel System Calibration
If the per channel system calibrations are used, these should be
initiated in the following order: a channel zero-scale system
calibration, followed by a channel full-scale system calibration.
The system calibration is affected by the ADC zero-scale and
full-scale calibration registers. Therefore, if both self-calibration
and system calibration are used in the system, an ADC full-
scale self-calibration should be performed first, followed by a
system calibration cycle.
While executing a system calibration, the fully settled system
zero-scale voltage signal or system full-scale voltage signal must
be connected to the selected channel analog inputs.
The per channel calibration registers can be read, stored, or
modified and written back to the AD7732. Note that when
writing the calibration registers the AD7732 must be in idle
mode. Note that outside the specified calibration range,
calibration is possible but the performance may degrade (see
the System Calibration section in Table 1).
相關PDF資料
PDF描述
AD7732BRUZ-REEL IC ADC 24BIT 2CH SIG-DEL 28TSSOP
AD7734BRUZ-REEL IC ADC 24BIT 4CH SIG-DEL 28TSSOP
MS27467T17A8P CONN PLUG 8POS STRAIGHT W/PINS
LTC2442IG#TRPBF IC ADC 24BIT 250MSPS 36-SSOP
MS27467E15F18PA CONN PLUG 18POS STRAIGHT W/PINS
相關代理商/技術參數
參數描述
AD7734 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, +-10 V Input Range, High Throughput, 24-Bit sigma ∆ ADC
AD7734BRU 功能描述:IC ADC 24BIT 4-CH 28-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極
AD7734BRU-REEL 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 3.05Msps 24-bit Serial 28-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 15.437KSPS 24BIT SERL 28TSSOP - Tape and Reel
AD7734BRU-REEL7 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 3.05Msps 24-bit Serial 28-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 15.437KSPS 24BIT SERL 28TSSOP - Tape and Reel
AD7734BRUZ 功能描述:IC ADC 24BIT 4-CH 28-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*