- 您現在的位置：買賣IC網 > PDF目錄10237 > AD7732BRUZ-REEL7 (Analog Devices Inc)IC ADC 24BIT 2CH SIG-DEL 28TSSOP PDF資料下載
參數資料
| 型號： | AD7732BRUZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 5/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 24BIT 2CH SIG-DEL 28TSSOP |
| 標準包裝： | 1,000 |
| 位數： | 24 |
| 采樣率（每秒）： | 15.4k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 100mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 28-TSSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個差分，單極；2 個差分，雙極 |
| 配用： | EVAL-AD7732EBZ-ND - BOARD EVAL FOR AD7732 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7732
Rev. A | Page 13 of 32
Pin No.
Mnemonic
Description
8
SYNC/P1
SYNC/Digital Input/Digital Output. The pin direction is determined by the P1 DIR bit;
the digital value can be read/written as the P1 bit in the I/O port register. When the
SYNC bit in the I/O port register is set to 1, the SYNC/P1 pin can be used to synchronize
the AD7732 modulator and digital filter with other devices in the system. The digital
voltage is referenced to analog supplies. When configured as an input, the pin should be
tied high or low.
9
RA
RA, in association with RB and BIAS0(+), can be used to level shift the positive analog
input 0. In normal circuit configuration, this pin is left open circuit.
10
RB
RB, in association with RA and BIAS0(+), can be used to level shift the positive analog
input 0. In normal circuit configuration, this pin is left open circuit.
11
BIAS1(+)
This input is used to level shift the positive analog input 1. This signal is used to ensure
that the differential signal seen by the internal buffer amplifier is within its common-
mode range. BIAS pins will normally be connected to 2.5 V.
12
AIN1(+)
Positive Analog Input Channel 1.
13
AIN0(+)
Positive Analog Input Channel 0.
14
BIAS0(+)
Voltage Bias for Positive Analog Input 0. This pin has the same function as BIAS1(+).
15
BIAS0(–)
Voltage Bias for Negative Analog Input 0. This pin has the same function as BIAS1(+).
16
AIN0(–)
Negative Analog Input Channel 0.
17
AIN1(–)
Negative Analog Input Channel 1.
18
BIAS1(–)
Voltage Bias for Negative Analog Input 1. This pin has the same function as BIAS1(+).
19
RC
RC, in association with RD and BIAS0(–), can be used to level shift the negative analog
input 0. In normal circuit configuration, this pin is left open circuit.
20
RD
RD, in association with RC and BIAS0(–), can be used to level shift the negative analog
input 0. In normal circuit configuration, this pin is left open circuit.
21
REFIN(+)
Positive Terminal of the Differential Reference Input. REFIN(+) voltage potential can lie
anywhere between AVDD and AGND. In normal circuit configuration, this pin should be
connected to a 2.5 V reference voltage.
22
REFIN(–)
Negative Terminal of the Differential Reference Input. REFIN(–) voltage potential can lie
anywhere between AVDD and AGND. In normal circuit configuration, this pin should be
connected to a 0 V reference voltage.
23
AGND
Ground Reference Point for Analog Circuitry.
24
RDY
Logic Output. Used as a status output in both conversion mode and calibration mode. In
conversion mode, a falling edge on this output indicates that either any channel or all
channels have unread data available, according to the RDYFN bit in the I/O port register.
In calibration mode, a falling edge on this output indicates that calibration is complete
(see the Digital Interface Description section for more details).
25
DOUT
Serial data output with serial data being read from the output shift register on the part.
This output shift register can contain information from any AD7732 register, depending
on the address bits of the communications register.
26
DIN
Serial data input (Schmitt triggered) with serial data being written to the input shift
register on the part. Data from this input shift register is transferred to any AD7732
register, depending on the address bits of the communications register.
27
DVDD
Digital Supply Voltage, 3 V or 5 V Nominal.
28
DGND
Ground Reference Point for Digital Circuitry.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7732BRUZ-REEL | IC ADC 24BIT 2CH SIG-DEL 28TSSOP |
| AD7734BRUZ-REEL | IC ADC 24BIT 4CH SIG-DEL 28TSSOP |
| MS27467T17A8P | CONN PLUG 8POS STRAIGHT W/PINS |
| LTC2442IG#TRPBF | IC ADC 24BIT 250MSPS 36-SSOP |
| MS27467E15F18PA | CONN PLUG 18POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7734 | 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, +-10 V Input Range, High Throughput, 24-Bit sigma ∆ ADC |
| AD7734BRU | 功能描述:IC ADC 24BIT 4-CH 28-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7734BRU-REEL | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 3.05Msps 24-bit Serial 28-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 15.437KSPS 24BIT SERL 28TSSOP - Tape and Reel |
| AD7734BRU-REEL7 | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 3.05Msps 24-bit Serial 28-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 15.437KSPS 24BIT SERL 28TSSOP - Tape and Reel |
| AD7734BRUZ | 功能描述:IC ADC 24BIT 4-CH 28-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
發布緊急采購，3分鐘左右您將得到回復。