- 您現在的位置：買賣IC網 > PDF目錄10279 > AD7766BRUZ-1-RL7 (Analog Devices Inc)IC ADC 24BIT 64KSPS SAR 16TSSOP PDF資料下載
參數資料
| 型號： | AD7766BRUZ-1-RL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 24BIT 64KSPS SAR 16TSSOP |
| 標準包裝： | 1,000 |
| 位數： | 24 |
| 采樣率（每秒）： | 64k |
| 數據接口： | 串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 18mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，單極 |
| 配用： | EVAL-AD7766EDZ-ND - BOARD EVAL AD7766 128KSPS 108DB EVAL-AD7766-2EDZ-ND - BOARD EVAL AD7766-2 32KSPS 114DB EVAL-AD7766-1EDZ-ND - BOARD EVAL AD7766-1 64KSPS 111DB |
AD7766
Rev. C | Page 17 of 24
AD7766/AD7766-1/AD77662-2 INTERFACE
The AD7766/AD7766-1/AD7766-2 provide the user with a
flexible serial interface, enabling the user to implement the
most desirable interfacing scheme for their application. Each
AD7766/AD7766-1/AD7766-2 interface comprises seven
different signals. Five of these signals are inputs: MCLK, CS,
SYNC/PD, SCLK, and SDI. The other two signals are outputs:
DRDY and SDO.
INITIAL POWER-UP
On initial power-up, apply a continuous MCLK signal. It is recom-
mended that the user reset the AD7766/AD7766-1/AD7766-2
to clear the filters and ensure correct operation. The reset is
completed as shown in Figure 5, with all events occurring relative
to the rising edge of MCLK. A negative pulse on the SYNC/PD
input initiates the reset, and the DRDY output switches to logic
high and remains high until valid data is available. Following the
power-up of the AD7766/AD7766-1/AD7766-2 by transitioning
the SYNC/PD pin to logic high, a settling time is required before
valid data is output by the device. This settling time, tSETTLING,
is a function of the MCLK frequency and the decimation rate.
lists the settling time of each AD7766 model and should
be referenced when reviewing
Table 7. Filter Settling Time After SYNC/PD
Model
Decimation Rate
tSETTLING 1
AD7766
8
(594 × tMCLK) + t21
AD7766-1
16
(1186 × tMCLK) + t21
AD7766-2
32
(2370 × tMCLK) + t21
1 tSETTLING is measured from the first MCLK rising edge after the rising edge of SYNC/PD
to the falling edge of DRDY.
READING DATA
The AD7766/AD7766-1/AD7766-2 output data conversion
results in an MSB-first, twos complement, 24-bit format on the
serial data output (SDO) pin. MCLK is the master clock, which
controls all the AD7766/AD7766-1/AD7766-2 conversions. The
SCLK is the serial clock input for the device. All data transfers
take place with respect to the SCLK signal.
The DRDY line is used as a status signal to indicate when the data
is available to be read from the AD7766/AD7766-1/AD7766-2.
The falling edge of DRDY indicates that a new data-word is
available in the output register of the device. DRDY stays low
during the period that output data is permitted to be read from
the SDO pin. The DRDY signal returns to logic high to indicate
when not to read from the device. Ensure that a data read is not
attempted during this period while the output register is being
updated.
The AD7766/AD7766-1/AD7766-2 offer the option of using a
chip select input signal (CS) in a data read cycle. The CS signal is
a gate for the SDO pin and allows many AD7766/AD7766-1/
AD7766-2 devices to share the same serial bus. It acts as an
instruction signal to each of these devices indicating permission
to use the bus. When CS is logic high, the SDO line of the
AD7766/AD7766-1/AD7766-2 is tristated.
There are two distinct patterns that can be initiated to read data
from the AD7766/AD7766-1/AD7766-2 devices: a pattern for
when the CS falling edge occurs after the DRDY falling edge
and a pattern for when the CS falling edge occurs before the
DRDY falling edge (when CS is set to logic low).
When the CS falling edge occurs after the DRDY falling edge,
the MSB of the conversion result is available on the SDO line on
the CS falling edge. The remaining bits of the conversion result
(MSB 1, MSB 2, and so on) are clocked onto the SDO line
by the falling edges of SCLK that follow the CS falling edge.
details this interfacing scheme.
When CS is tied low, the AD7766/AD7766-1/AD7766-2 serial
interfaces can operate in 3-wire mode as shown in
. In
this case, the MSB of the conversion result is available on the
SDO line on the falling edge of
DRDY. The remaining bits of
the data conversion result (MSB 1, MSB 2, and so on) are
clocked onto the SDO line by the subsequent SCLK falling edges.
POWER-DOWN, RESET, AND SYNCHRONIZATION
The SYNC/PD pin allows the user to synchronize multiple
AD7766/AD7766-1/AD7766-2 devices. This pin also allows the
user to reset and power down the AD7766/AD7766-1/AD7766-2
devices. These features are implemented relative to the rising edges
of MCLK and are shown in
, marked as A, B, C, and D.
To power down, reset, or synchronize a device, the SYNC/PD
pin should be taken low. On the first rising edge of MCLK, the
AD7766/AD7766-1/AD7766-2 are powered down. The DRDY
pin transitions to logic high, indicating that the data in the
output register is no longer valid. The status of the SYNC/PD
pin is checked on each subsequent rising edge of MCLK. On the
first rising edge of MCLK after the SYNC/PD pin is taken high,
the AD7766/AD7766-1/AD7766-2 are taken out of power-down.
On the next rising edge, the filter of the AD7766/AD7766-1/
AD7766-2 is reset. On the following rising edge, the first new
sample is taken.
A settling time, tSETTLING, from the filter reset must elapse before
valid data is output by the device (see Table 7). The DRDY
output goes logic low after tSETTLING to indicate when valid data is
available on SDO for readback.
相關PDF資料 |
PDF描述 |
|---|---|
| MS27497T24B4SLC | CONN HSG RCPT 56POS WALL MT SCKT |
| VE-JN4-MX-S | CONVERTER MOD DC/DC 48V 75W |
| MS27505E15B15PA | CONN RCPT 15POS BOX MNT W/PINS |
| D38999/20MG11BN | CONN HSG RCPT 11POS WALL MT SCKT |
| VE-JN3-MX-S | CONVERTER MOD DC/DC 24V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7766BRUZ-2 | 功能描述:IC ADC 24BIT 32KSPS SAR 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7766BRUZ-2-RL7 | 功能描述:IC ADC 24BIT 32KSPS SAR 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7766BRUZ-RL7 | 功能描述:IC ADC 24BIT 128KSPS SAR 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7767 | 制造商:AD 制造商全稱:Analog Devices 功能描述:24-Bit, 8.5 mW, 109 dB, 128/64/32 kSPS ADCs |
| AD7767BRUZ | 功能描述:ADC 24BIT 128KSPS SAR 16-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
發(fā)布緊急采購，3分鐘左右您將得到回復。