VREF+ INPUT SIGNAL The AD7766/AD7" />
參數資料
型號: AD7766BRUZ-1-RL7
廠商: Analog Devices Inc
文件頁數: 16/25頁
文件大小: 0K
描述: IC ADC 24BIT 64KSPS SAR 16TSSOP
標準包裝: 1,000
位數: 24
采樣率(每秒): 64k
數據接口: 串行
轉換器數目: 1
功率耗散(最大): 18mW
電壓電源: 模擬和數字
工作溫度: -40°C ~ 105°C
安裝類型: 表面貼裝
封裝/外殼: 16-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 16-TSSOP
包裝: 帶卷 (TR)
輸入數目和類型: 1 個差分,單極
配用: EVAL-AD7766EDZ-ND - BOARD EVAL AD7766 128KSPS 108DB
EVAL-AD7766-2EDZ-ND - BOARD EVAL AD7766-2 32KSPS 114DB
EVAL-AD7766-1EDZ-ND - BOARD EVAL AD7766-1 64KSPS 111DB
AD7766
Rev. C | Page 22 of 24
VREF+ INPUT SIGNAL
The AD7766/AD7766-1/AD7766-2 VREF + pin is supplied with a
voltage in the range of 2.4 V to 2 × AVDD (nominally 5 V). It is
recommended that the VREF+ input be generated by a low noise
voltage reference. Examples of such references are the ADR445,
ADR435, ADR425 (5 V output), and ADR421 (2.5 V output).
Typical reference supply circuits are shown in Figure 46.
The reference voltage input pin (VREF+) also acts as a power
supply to the AD7766/AD7766-1/AD7766-2 devices. For a 5 V
VREF+ input, a full-scale input of 5 V on both VIN+ and VIN can
be applied while voltage supplies to pins AVDD remain at 2.5 V.
This configuration reduces the number of different supplies
required.
The output of the low noise voltage reference does not require a
buffer; however, decoupling the output of the low noise reference is
important. Place a 0.1 μF capacitor at the output of the voltage
reference devices (ADR445, ADR435, ADR425, and ADR421)
and follow the decoupling advice provided for the reference
device chosen.
As mentioned, the nominal supply to the VREF+ pin is 5 V to
achieve the full dynamic range available. When a 2.5 V VREF+
input is used (that is, in low power applications), the signal-to-
noise ratio and dynamic range figures (generated using a 5 V
VREF+ input) quoted in the Specifications section decrease by
6 dB, a direct result of halving the available input range.
The AD7766/AD7766-1/AD7766-2 devices require a 100 μF
capacitor to ground, which acts as a decoupling capacitor and as
a reservoir of charge for the VREF+ pin. Place this capacitor as
close to the AD7766/AD7766-1/AD7766-2 devices as possible.
Reducing the value of this capacitor (C40 in Figure 46) to 10 μF
typically degrades noise performance by 1 dB. C40 can be an
electrolytic or tantalum capacitor.
06
44
9-
2
29
C39
0.1F
C40
100F
C34
10F
C35
0.1F
AD7766/
AD7766-1/
AD7766-2
ADR4xx
VOUT
V
REFERENCE
SUPPLY
V+
REF+
VIN
Figure 46. AD7766/AD7766-1/AD7766-2 Reference Input Configuration
MULTIPLEXING ANALOG INPUT CHANNELS
The AD7766/AD7766-1/AD7766-2 can be used with a multi-
plexer configuration. As per any converter that uses a digital
filtering block, the maximum switching rate or the output data
rate per channel is a function of the digital filter settling time.
A user multiplexing the analog inputs to a converter that
employs a digital filter must wait the full digital filter settling
time before a valid conversion result can be achieved; after this
settling time, the channel can be switched. Then, the full
settling time must again be observed before a valid conversion
result is available and the input is switched once more.
The AD7766 filter settling time equals 74 divided by the output
data rate in use. The maximum switching frequency in a multi-
plexed application is, therefore, 1/(74/ODR), where the output
data rate (ODR) is a function of the applied MCLK frequency
and the decimation rate employed by the device in question. For
example, applying a 1.024 MHz MCLK frequency to the AD7766
results in a maximum output data rate of 128 kHz, which in
turn allows a 1.729 kHz multiplexer switching rate.
The AD7766-1 and the AD7766-2 employ digital filters with
longer settling time to achieve greater precision; thus, the
maximum switching frequency for these devices is 864 Hz and
432 Hz, respectively.
相關PDF資料
PDF描述
MS27497T24B4SLC CONN HSG RCPT 56POS WALL MT SCKT
VE-JN4-MX-S CONVERTER MOD DC/DC 48V 75W
MS27505E15B15PA CONN RCPT 15POS BOX MNT W/PINS
D38999/20MG11BN CONN HSG RCPT 11POS WALL MT SCKT
VE-JN3-MX-S CONVERTER MOD DC/DC 24V 75W
相關代理商/技術參數
參數描述
AD7766BRUZ-2 功能描述:IC ADC 24BIT 32KSPS SAR 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率(每秒):1M 數據接口:串行,SPI? 轉換器數目:1 功率耗散(最大):- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤(4x4) 包裝:Digi-Reel® 輸入數目和類型:8 個單端,單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
AD7766BRUZ-2-RL7 功能描述:IC ADC 24BIT 32KSPS SAR 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
AD7766BRUZ-RL7 功能描述:IC ADC 24BIT 128KSPS SAR 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
AD7767 制造商:AD 制造商全稱:Analog Devices 功能描述:24-Bit, 8.5 mW, 109 dB, 128/64/32 kSPS ADCs
AD7767BRUZ 功能描述:ADC 24BIT 128KSPS SAR 16-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率(每秒):1M 數據接口:串行,SPI? 轉換器數目:1 功率耗散(最大):- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤(4x4) 包裝:Digi-Reel® 輸入數目和類型:8 個單端,單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6