- 您現在的位置：買賣IC網 > PDF目錄10143 > AD7778ASZ (Analog Devices Inc)IC ADC 10BIT 8CHAN HS 44-MQFP PDF資料下載
參數資料
| 型號： | AD7778ASZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 2/12頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 8CHAN HS 44-MQFP |
| 標準包裝： | 1 |
| 位數： | 10 |
| 采樣率（每秒）： | 378k |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-QFP |
| 供應商設備封裝： | 44-MQFP（10x10） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 8 個單端，單極 |
AD7776/AD7777/AD7778
–10–
REV. A
Short Circuit Current
This is defined as the maximum current which flows either
into or out of the REFOUT pin if this pin is shorted to any
potential between 0 V and VCC. This condition can be allowed
for up to 10 seconds provided that the power dissipation of the
package is not exceeded.
Signal-to-Noise and Distortion Ratio, S/(N+D)
Signal-to-noise and distortion ratio, S/(N+D), is the ratio of the
rms value of the measured input signal to the rms sum of all
other spectral components below the Nyquist frequency, includ-
ing harmonics, but excluding dc. The value for S/(N+D) is
given in decibels.
Total Harmonic Distortion, THD
Total harmonic distortion is the ratio of the rms sum of the first
five harmonic components to the rms value of a full-scale input
signal and is expressed in decibels. For the AD7776/AD7777/
AD7778, total harmonic distortion (THD) is defined as:
20
2
3
2
4
2
5
2
6
2
12
1
log
VVV
VV
V
++
()
where V1 is the rms amplitude of the fundamental and V2,
V3, V4, V5, and V6 are the rms amplitudes of the individual
harmonics.
Intermodulation Distortion, IMD
With inputs consisting of sine waves at two frequencies, fa and fb,
any active device with nonlinearities creates distortion products,
of order (m + n), at sum and difference frequencies of mfa + nfb,
where m, n = 0, 1, 2, 3. Intermodulation terms are those for which
m or n is not equal to zero. For example, the second order terms
include (fa + fb) and (fa – fb) and the third order terms include
(2 fa + fb), (2 fa – fb), (fa + 2 fb), and (fa – 2 fb).
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of cross-talk
between channels. It is measured by applying a full-scale 100 kHz
sine wave signal to any one of the input channels and monitoring
the remaining channels. The figure given is the worst case across
all channels.
DIGITAL SIGNAL PROCESSING APPLICATIONS
In digital signal processing (DSP) application areas like voice
recognition, echo cancellation, and adaptive filtering, the dynamic
characteristics S/(N+D), THD, and IMD of the ADC are critical.
The AD7776/AD7777/AD7778 are specified dynamically as well
as with standard dc specifications. Because the track/hold
amplifier has a wide bandwidth, an antialiasing filter should be
placed on the analog inputs to avoid aliasing high frequency noise
back into the bands of interest.
The dynamic performance of the ADC is evaluated by applying a
sine wave signal of very low distortion to a single analog input
which is sampled at 380.95 kHz. A fast Fourier transform (FFT)
plot or histogram plot is then generated from which the signal to
noise and distortion, harmonic distortion, and dynamic differential
nonlinearity data can be obtained. Similarly, for intermodulation
distortion, an input signal consisting of two pure sine waves at
different frequencies is applied to the AD7776/AD7777/AD7778.
Figure 11 shows a 2048-point FFT plot for a single channel of
the AD7778 with an input signal of 99.88 kHz. The SNR is
58.71 dB. It can be seen that most of the harmonics are buried
in the noise floor. It should be noted that the harmonics are
taken into account when calculating the S/(N+D).
0
–90
–80
0
–60
–40
–20
99.88
SIGNAL
AMPLITUDE
–
dB
FREQUENCY – kHz
INPUT FREQUENCY =
99.88kHz
SAMPLE FREQUENCY =
380.95kHz
SNR = 58.7dB
TA = 25 C
Figure 11. ADC FFT Plot
The relationship between S/(N+D) and resolution (n) is ex-
pressed by the following equation:
SN
D
n
dB
+
() =+
()
602
176
..
This is for an ideal part with no differential or integral linearity
errors. These errors cause a degradation in S/(N+D). By work-
ing backwards from the above equation, it is possible to get a
measure of ADC performance expressed in effective number
of bits (n).
n effective
SN
D
dB
() =
+
()( ) 176
602
.
The effective number of bits plotted versus frequency for a
single channel of the AD7778 is shown in Figure 12. The effec-
tive number of bits is typically 9.5.
10.0
7.5
189.2
9.0
8.0
8.5
0
9.5
INPUT FREQUENCY – kHz
EFFECTIVE
NUMBER
OF
BITS
SAMPLE FREQUENCY = 378.4kHz
TA = 24 C
Figure 12. Effective Number of Bits vs. Frequency
相關PDF資料 |
PDF描述 |
|---|---|
| VI-223-IW-F4 | CONVERTER MOD DC/DC 24V 100W |
| LTC2247IUH#TRPBF | IC ADC 14BIT 40MSPS SAMPL 32-QFN |
| VI-223-IW-F2 | CONVERTER MOD DC/DC 24V 100W |
| VE-BN0-MW-F2 | CONVERTER MOD DC/DC 5V 100W |
| AD7858BR | IC ADC 12BIT 8CH SRL 24-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7779ACPZ | 功能描述:24 Bit Analog to Digital Converter 8 Input 8 Sigma-Delta 64-LFCSP (9x9) 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態(tài):有效 位數:24 采樣率（每秒）:16k 輸入數:8 輸入類型:差分，單端 數據接口:串行 配置:PGA-ADC 無線電 - S/H:ADC:- A/D 轉換器數:8 架構:三角積分 參考類型:外部， 內部 電壓 - 電源，模擬:±1.65V，2.2 V ~ 3.6 V 電壓 - 電源，數字:- 特性:同步采樣 工作溫度:-40°C ~ 125°C 封裝/外殼:64-WFQFN 裸露焊盤 供應商器件封裝:64-LFCSP（9x9） 標準包裝:1 |
| AD7779ACPZ-RL | 功能描述:IC ADC 24BIT 16KSPS 制造商:analog devices inc. 系列:* 零件狀態(tài):有效 標準包裝:2,500 |
| AD7780 | 制造商:AD 制造商全稱:Analog Devices 功能描述:24-Bit, Pin-Programmable, Ultralow Power Sigma-Delta ADC |
| AD7780BRUZ | 功能描述:IC ADC 24BIT 1CH LP SD 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7780BRUZ-REEL | 功能描述:IC ADC 24BIT 1CH LP SD 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
發(fā)布緊急采購，3分鐘左右您將得到回復。