- 您現在的位置：買賣IC網 > PDF目錄10143 > AD7778ASZ (Analog Devices Inc)IC ADC 10BIT 8CHAN HS 44-MQFP PDF資料下載
參數資料
| 型號： | AD7778ASZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT 8CHAN HS 44-MQFP |
| 標準包裝： | 1 |
| 位數： | 10 |
| 采樣率（每秒）： | 378k |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-QFP |
| 供應商設備封裝： | 44-MQFP（10x10） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 8 個單端，單極 |
AD7776/AD7777/AD7778
–5–
REV. A
PIN FUNCTION DESCRIPTION
Mnemonic
Description
VCC
+5 V Power Supply.
AGND
Analog Ground.
DGND
Digital Ground. Ground reference for digital circuitry.
DB0–DB9
Input/Output Data Bus. This is a bidirectional data port from which ADC output data may be read and to which
control register data may be written.
BUSY/INT
Busy/Interrupt Output. Active low logic output indicating A/D converter status. This logic output has two modes
of operation depending on whether location CR9 of the control register has been set low or high:
If CR9 is set low, the
BUSY/INT output behaves as a BUSY signal. The BUSY signal goes low and stays low for the
duration of a single conversion, or if simultaneous sampling has been selected,
BUSY stays low for the duration of
both conversions.
If CR9 is set high,
BUSY/INT output behaves as an INTERRUPT signal. The INT signal goes low and remains low
after either a single conversion is completed or after a double conversion is completed if simultaneous sampling has
been selected. With CR9 high, the falling edge of
WR or RD resets the INT line high.
CS
Chip Select Input. The device is selected when this input is low.
WR
Write Input (Active Low). It is used in conjunction with
CS to write data to the control register. Data is latched to the
registers on the rising edge of
WR. Following the rising edge of WR, the analog input is acquired and a conversion is
started.
RD
Read Input (Active Low). It is used in conjunction with
CS to enable the data outputs from the ADC registers.
AIN1–8
Analog Inputs 1–8. The analog input range is VBIAS
± V
SWING where VBIAS and VSWING are defined by the reference
voltage applied to REFIN. Input resistance between any of the analog input pins and AGND is 10 k
or greater.
REFIN
Voltage Reference Input. The AD7776/AD7777/AD7778 are specified over a voltage reference range of 1.9 V to 2.1 V
with a nominal value of 2.0 V. This REFIN voltage provides the VBIAS and VSWING levels for the input channel(s).
VBIAS is equal to REFIN and VSWING is nominally equal to REFIN/2. Input resistance between this REFIN pin and
AGND is 10 k
or greater.
REFOUT
Voltage Reference Output. This pin provides the internal voltage reference, which is nominally 2.0 V. It can provide
the bias voltage (VBIAS) for the input channel(s).
CREFIN
Reference Decoupling Capacitor. A 10 nF capacitor must be connected from this pin to AGND to ensure correct
operation of the high speed ADC.
RTN
Signal Return Path for the input channel(s). Normally RTN is connected to AGND at the package.
CIRCUIT DESCRIPTION
ADC Transfer Function
For all versions, an input signal of the form VBIAS
± VSWING is
expected. This VBIAS signal level operates as a pseudo ground to
which all input signals must be referred. The VBIAS level is
determined by the voltage applied to the REFIN pin. This can
be driven by an external voltage source or, alternatively, by the
onboard 2 V reference, available at REFOUT. The magnitude
of the input signal swing is equal to VBIAS/2 (or REFIN/2) and is
set internally. With a REFIN of 2 V, the analog input signal level
varies from 1 V to 3 V, i.e., 2
± 1 V. Figure 5 shows the transfer
function of the ADC and its relationship to VBIAS and VSWING.
The half-scale two's complement code of the ADC, 000 Hex (00
0000 0000 Binary), occurs at an input voltage equal to VBIAS. The
input full-scale range of the ADC is equal to 2 VSWING, so that the
Plus Full-Scale transition (1FE to 1FF) occurs at a voltage equal to
VBIAS + VSWING – 1.5 LSBs, and the minus full-scale code transi-
tion (200 to 201) occurs at a voltage VBIAS – VSWING + 0.5 LSBs.
ADC
OUTPUT
CODE
(HEX)
1FF
1FE
202
201
200
000
VBIAS–VSWING
VBIAS
VBIAS+VSWING
ANALOG INPUT, VIN
Figure 5. ADC Transfer Function
相關PDF資料 |
PDF描述 |
|---|---|
| VI-223-IW-F4 | CONVERTER MOD DC/DC 24V 100W |
| LTC2247IUH#TRPBF | IC ADC 14BIT 40MSPS SAMPL 32-QFN |
| VI-223-IW-F2 | CONVERTER MOD DC/DC 24V 100W |
| VE-BN0-MW-F2 | CONVERTER MOD DC/DC 5V 100W |
| AD7858BR | IC ADC 12BIT 8CH SRL 24-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7779ACPZ | 功能描述:24 Bit Analog to Digital Converter 8 Input 8 Sigma-Delta 64-LFCSP (9x9) 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:有效 位數:24 采樣率（每秒）:16k 輸入數:8 輸入類型:差分，單端 數據接口:串行 配置:PGA-ADC 無線電 - S/H:ADC:- A/D 轉換器數:8 架構:三角積分 參考類型:外部， 內部 電壓 - 電源，模擬:±1.65V，2.2 V ~ 3.6 V 電壓 - 電源，數字:- 特性:同步采樣 工作溫度:-40°C ~ 125°C 封裝/外殼:64-WFQFN 裸露焊盤 供應商器件封裝:64-LFCSP（9x9） 標準包裝:1 |
| AD7779ACPZ-RL | 功能描述:IC ADC 24BIT 16KSPS 制造商:analog devices inc. 系列:* 零件狀態:有效 標準包裝:2,500 |
| AD7780 | 制造商:AD 制造商全稱:Analog Devices 功能描述:24-Bit, Pin-Programmable, Ultralow Power Sigma-Delta ADC |
| AD7780BRUZ | 功能描述:IC ADC 24BIT 1CH LP SD 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7780BRUZ-REEL | 功能描述:IC ADC 24BIT 1CH LP SD 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
發布緊急采購，3分鐘左右您將得到回復。