access the result from Channel B (V
參數資料
型號: AD7862BRZ-3
廠商: Analog Devices Inc
文件頁數: 16/16頁
文件大?。?/td> 0K
描述: IC ADC 12BIT DUAL 250KSPS 28SOIC
標準包裝: 27
位數: 12
采樣率(每秒): 250k
數據接口: 并聯
轉換器數目: 2
功率耗散(最大): 75mW
電壓電源: 模擬和數字
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 28-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 28-SOIC W
包裝: 管件
輸入數目和類型: 4 個單端,雙極
AD7862
–9–
REV. 0
and fourth read pulses, after the second conversion and A0 high,
access the result from Channel B (VB1 and VB2 respectively). A0’s
state can be changed any time after the CONVST goes high,
i.e., track/holds into hold, and 400 ns prior to the next falling
edge of CONVST. Data is read from the part via a 12-bit
parallel data bus with standard CS and RD signal, i.e., the read
operation consists of a negative going pulse on the CS pin
combined with two negative going pulses on the RD pin (while
the CS is low), accessing the two 12-bit results. Once the read
operation has taken place, a further 300 ns should be allowed
before the next falling edge of CONVST to optimize the settling
of the track/hold amplifier before the next conversion is initiated.
With the internal clock frequency at its maximum (3.7 MHz—not
accessible externally), the achievable throughput rate for the
part is 3.6
s (conversion time) plus 100 ns (read time) plus
0.3
s (acquisition time). This results in a minimum throughput
time of 4
s (equivalent to a throughput rate of 250 kHz).
Read Options
Apart from the read operation described above and displayed in
Figure 5a, other CS and RD combinations can result in
different channels/inputs being read in different combinations.
Suitable combinations are shown in Figures 5b through 5d.
VA1
VA2
CS
RD
DATA
Figure 5b. Read Option A
VA1
VA2
CS
RD
DATA
VA1
Figure 5c. Read Option B
VA1
VB1
A0
CS
RD
DATA
Figure 5d. Read Option C
OPERATING MODES
Mode 1 Operation (High Sampling Performance)
The timing diagram in Figure 5a is for optimum performance in
operating mode 1 where the falling edge of CONVST starts
conversion and puts the track/hold amplifiers into their hold
mode. This falling edge of CONVST also causes the BUSY
signal to go high to indicate that a conversion is taking place.
The BUSY signal goes low when the conversion is complete,
which is 3.6
s max after the falling edge of CONVST, and new
data from this conversion is available in the output latch of the
AD7862. A read operation accesses this data. If the multiplexer
select A0 is low, the first and second read pulses after the first
conversion access the result from Channel A (VA1 and VA2
VA1
VA2
VB1
VB2
t
3
t
1
t
2
t
4
t
5
t
6
t
CONV = 3.6s
t7
CONVST
BUSY
A0
CS
RD
DATA
300ns
400ns
Figure 5a. Mode 1 Timing Operation Diagram for High Sampling Performance
相關PDF資料
PDF描述
VI-22H-IX-B1 CONVERTER MOD DC/DC 52V 75W
VE-BN0-MW-F4 CONVERTER MOD DC/DC 5V 100W
VI-22H-IW-F4 CONVERTER MOD DC/DC 52V 100W
MS3112E10-98PX CONN RCPT 6POS BOX MNT W/PINS
IDT7200L20SO8 IC MEM FIFO 256X9 20NS 28-SOIC
相關代理商/技術參數
參數描述
AD7862SQ-10 制造商:AD 制造商全稱:Analog Devices 功能描述:Simultaneous Sampling Dual 250 kSPS 12-Bit ADC
AD7863 制造商:AD 制造商全稱:Analog Devices 功能描述:Simultaneous Sampling Dual 175 kSPS 14-Bit ADC
AD7863AR-10 功能描述:IC ADC 14BIT DUAL 2CH 28-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率(每秒):83k 數據接口:串行,并聯 轉換器數目:1 功率耗散(最大):95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP(0.600",15.24mm) 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端,雙極
AD7863AR-10REEL 功能描述:IC ADC 14BIT DUAL 2CH 28-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率(每秒):83k 數據接口:串行,并聯 轉換器數目:1 功率耗散(最大):95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP(0.600",15.24mm) 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端,雙極
AD7863AR-10REEL7 制造商:Analog Devices 功能描述:ADC Dual SAR 175ksps 14-bit Parallel 28-Pin SOIC W T/R