- 您現在的位置：買賣IC網 > PDF目錄11786 > AD7869JNZ (Analog Devices Inc)IC I/O PORT 14BIT ANLG 24DIP PDF資料下載
參數資料
| 型號： | AD7869JNZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I/O PORT 14BIT ANLG 24DIP |
| 標準包裝： | 1 |
| 應用： | 模擬 I/O |
| 接口： | TTL/CMOS |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 封裝/外殼： | 24-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 24-PDIP |
| 包裝： | 管件 |
| 安裝類型： | 通孔 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁
AD7869
–6–
CONVERTER DETAILS
The AD7869 is a complete 14-bit I/O port; the only external
components required for normal operation are pull-up resistors
for the ADC data outputs, and power supply decoupling capaci-
tors. The AD7869 is comprised of a 14-bit successive approxi-
mation ADC with a track/hold amplifier, a 14-bit DAC with a
buffered output and two 3 V buried Zener references, a clock os-
cillator and control logic.
ADC CLOCK
The AD7869 has an internal clock oscillator that can be used for
the ADC conversion procedure. The oscillator is enabled by ty-
ing the CLK input to VSS. The oscillator is laser trimmed at the
factory to give a maximum conversion time of 10
s. The mark/
space ratio can vary from 40/60 to 60/40. Alternatively, an exter-
nal TTL compatible clock may be applied to this input. The al-
lowable mark/space ratio of an external clock is 40/60 to 60/40.
RCLK is a clock output, used for the serial interface. This out-
put is derived directly from the ADC clock source and can be
switched off at the end of conversion with the CONTROL
input.
ADC CONVERSION TIMING
The conversion time for both external clock and continuous in-
ternal clock can vary from 19 to 20 rising clock edges, depending
on the conversion start to ADC clock synchronization. If a con-
version is initiated within 30 ns prior to a rising edge of the ADC
clock, the conversion time will consist of 20 rising clock edges,
i.e., 9.5
s conversion time. For noncontinuous internal clock,
the conversion time always consists of 19 rising clock edges.
ADC TRACK-AND-HOLD AMPLIFIER
The track-and-hold amplifier on the analog input of the AD7869
allows the ADC to accurately convert an input sine wave of 6 V
peak–peak amplitude to 14-bit accuracy. The input impedance is
typically 9 k
; an equivalent circuit is shown in Figure 1. The
input bandwidth of the track/hold amplifier is much greater
than the Nyquist rate of the ADC even when the ADC is oper-
ated at its maximum throughput rate. The 0.1 dB cutoff fre-
quency occurs typically at 500 kHz. The track/hold amplifier
acquires an input signal to 14-bit accuracy in less than 2
s. The
overall throughput rate is equal to the conversion time plus the
track/hold amplifier acquisition time. For a 2.0 MHz input clock,
the throughput time is 12
s max.
AD7869*
4.5k
4.5k
*ADDITIONAL PINS OMITTED FOR CLARITY
VIN
TO INTERNAL
COMPARATOR
TRACK/HOLD
AMPLIFIER
TO INTERNAL
3V REFERENCE
Figure 1. ADC Analog Input
The operation of the track/hold amplifier is essentially transpar-
ent to the user. The track/hold amplifier goes from its track
mode to its hold mode at the start of conversion on the rising
edge of
CONVST.
INTERNAL REFERENCES
The AD7869 has two on-chip temperature compensated buried
Zener references that are factory trimmed to 3 V
±10 mV. One
reference provides the appropriate biasing for the ADC, while
the other is available as a reference for the DAC. Both reference
outputs are available (labelled RO DAC and RO ADC) and are
capable of providing up to 500
A to an external load.
The DAC input reference (RI DAC) can be sourced externally
or connected to any of the two on-chip references. Applications
requiring good full-scale error matching between the DAC and
the ADC should use the ADC reference as shown in Figure 4.
The maximum recommended capacitance on either of the refer-
ence output pins for normal operation is 50 pF. If either of the
reference outputs is required to drive a capacitive load greater
than 50 pF, then a 200
resistor must be placed in series with
the capacitive load. The addition of decoupling capacitors,
10
F in parallel with 0.1 F as shown in Figure 2, improves
noise performance. The improvement in noise performance can
be seen from the graph in Figure 3. Note: this applies for the
DAC output only; reference decoupling components do not af-
fect ADC performance. Consequently, a typical application will
have just the DAC reference decoupled with the other one open
circuited.
RI DAC
200
RO DAC
or
RO ADC*
EXT LOAD
GREATER THAN 50pF
*RO DAC/RO ADC CAN BE LEFT
OPEN CIRCUIT IF NOT USED
10
F
0.1
F
Figure 2. Reference Decoupling Components
DAC OUTPUT AMPLIFIER
The output from the voltage mode DAC is buffered by a non-
inverting amplifier. The buffer amplifier is capable of developing
±3 V across 2 k and 100 pF load to ground and can produce
6 V peak-to-peak sine wave signals to a frequency of 20 kHz.
The output is updated on the falling edge of the LDAC input.
The output voltage settling time, to within 1/2 LSB of its final
value, is typically less than 3.5
s.
The small signal (200 mV p–p) bandwidth of the output buffer
amplifier is typically 1 MHz. The output noise from the ampli-
fier is low with a figure of 30 nV/
√Hz at a frequency of 1 kHz.
The broadband noise from the amplifier exhibits a typical peak-
to-peak figure of 150
V for a 1 MHz output bandwidth. Figure
3 shows a typical plot of noise spectral density versus frequency
for the output buffer amplifier and for either of the on-chip
references.
REV. B
相關PDF資料 |
PDF描述 |
|---|---|
| AD6641BCPZ-500 | IC IF RCVR 11BIT 200MSPS 56LFCSP |
| VI-JTJ-IW-F3 | CONVERTER MOD DC/DC 36V 100W |
| VI-JTJ-IW-F2 | CONVERTER MOD DC/DC 36V 100W |
| 1604037-4 | CONN HOUSING POWER 2POLE BATTERY |
| VI-JTH-IW-F4 | CONVERTER MOD DC/DC 52V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7869JQ | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AD7869JR | 制造商:Analog Devices 功能描述:Data Acquisition System Single ADC Single DAC 14-Bit 28-Pin SOIC W 制造商:Analog Devices 功能描述:DATA ACQ SYS SGL ADC SGL DAC 14BIT 28SOIC W - Rail/Tube |
| AD7869JRZ | 功能描述:IC I/O PORT 14BIT ANLG 28SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD7870 | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Complete, 12-Bit, 100 kHz, Sampling ADCs |
| AD7870A | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Complete, 12-Bit, 100 kHz , Sampling ADC |
發布緊急采購，3分鐘左右您將得到回復。