- 您現在的位置：買賣IC網 > PDF目錄9737 > AD7877ACPZ-500RL7 (Analog Devices Inc)IC ADC 12BIT TOUCHSCREEN 32LFCSP PDF資料下載
參數資料
| 型號： | AD7877ACPZ-500RL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/45頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT TOUCHSCREEN 32LFCSP |
| 標準包裝： | 1 |
| 類型： | 電阻 |
| 觸摸面板接口： | 4 線 |
| 輸入數/鍵： | 1 TSC |
| 分辨率（位）： | 12 b |
| 評估套件： | 可供 |
| 數據接口： | 串行，SPI? |
| 數據速率/采樣率 (SPS，BPS)： | 125k |
| 電壓基準： | 外部，內部 |
| 電源電壓： | 2.7 V ~ 5.25 V |
| 電流 - 電源： | 1µA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 32-LFCSP-VQ |
| 包裝： | 標準包裝 |
| 其它名稱： | AD7877ACPZ-500RL7DKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
AD7877
Data Sheet
Rev. D | Page 16 of 44
For greater accuracy, the ratiometric method has two significant
advantages:
The reference to the ADC is provided from the actual
voltage across the screen; therefore, when the voltage drops
across the switches, it has no effect.
Because the measurement is ratiometric, it does not matter
if the voltage across the screen varies in the long term.
However, it must not change after the signal has been
acquired.
The disadvantage of the ratiometric method is that the screen
must be powered up at all times because it provides the
reference voltage for the ADC.
TOUCH-PRESSURE MEASUREMENT
The pressure applied to the touch screen via a pen or finger can
also be measured with the AD7877 using some simple calcula-
tions. The contact resistance between the X and Y plates is
measured providing a good indication of the size of the
depressed area and, therefore, the applied pressure. The area of
the spot that is touched is proportional to the size of the object
touching it. The size of this resistance (RTOUCH) can be calculated
using two different methods.
First Method
The first method requires the user to know the total resistance
of the X-plate tablet (RX). Three touch screen conversions are
required:
Measurement of the X position, XPOSITION (Y+ input).
Measurement of the Y input with the excitation voltage
applied to Y+ and X (Z1 measurement).
Measurement of the X+ input with the excitation voltage
applied to Y+ and X (Z2 measurement).
These three measurements are illustrated in Figure 31.
The AD7877 has two special ADC channel settings that
configure the X and Y switches for Z1 and Z2 measurement and
store the results in the Z1 and Z2 results registers. The Z1
measurement is ADC Channel 1010b, and the result is stored in
the register with Read Address 11010b. The Z2 measurement is
ADC Channel 0010b, and the result is stored in the register with
Read Address 10010b.
The touch resistance can then be calculated using the following
equation:
RTOUCH = (RXPlate) × (XPOSITION /4096 × [Z2/Z1) 1]
(2)
03796-009
Y–
Y+
X–
X+
TOUCH
RESISTANCE
MEASURE
Z1 POSITION
X–
X+
Y–
Y+
TOUCH
RESISTANCE
MEASURE
X POSITION
Y–
Y+
X–
X+
TOUCH
RESISTANCE
MEASURE
Z2 POSITION
Figure 31. Three Measurements Required for Touch Pressure
Second Method
The second method requires the user to know the resistance of
the X-plate and Y-plate tablets. Three touch screen conversions
are required, a measurement of the X position (XPOSITION),
Y position (YPOSITION), and Z1 position.
The following equation also calculates the touch resistance:
RTOUCH = RXPlate × (XPOSITION /4096) × [(4096/Z1) 1]
RYPlate × [1 (YPOSITION/4096)]
(3)
STOPACQ PIN
As previously explained in the Touch Screen Principles section,
touch screens are composed of two resistive layers, normally
placed over an LCD screen. Because these layers are in close
proximity to the LCD screen, noise can be coupled from the
screen onto these resistive layers, causing errors in the touch
screen positional measurements.
For example, a jitter might be noticeable in the cursor on-screen.
In most LCD touch screen systems, a signal, such as an LCD
invert signal or other control signal, is present, and noise is
usually coupled onto the touch screen during the active period
of this signal (see Figure 32).
03796-010
LCD SIGNAL
TOUCH SCREEN
SIGNAL
NOISY
PERIOD
NOISY
PERIOD
Figure 32. Effect of LCD Noise on Touch Screen Measurements
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/20WJ29PD | CONN RCPT 29POS WALL MNT W/PINS |
| D38999/20FJ29PB | CONN RCPT 29POS WALL MNT W/PINS |
| D38999/20WJ29PB | CONN RCPT 29POS WALL MNT W/PINS |
| SY100EL12ZI | IC DRIVER LOW IMPEDANCE 8-SOIC |
| AD7873ACPZ | IC ADC 12BIT TOUCHSCREEN 16LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7877ACPZ-REEL | 功能描述:IC ADC 12BIT TOUCHSCREEN 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD7877ACPZ-REEL7 | 功能描述:IC ADC 12BIT TOUCHSCREEN 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD7877WACPZ-REEL7 | 功能描述:IC CTRLR TOUCH SCREEN 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD7878 | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface |
| AD7878AQ | 制造商:Rochester Electronics LLC 功能描述:COMPLETE 12 BIT ADC IC - Bulk |
發布緊急采購，3分鐘左右您將得到回復。