- 您現在的位置：買賣IC網 > PDF目錄10043 > AD7878JNZ (Analog Devices Inc)IC ADC 12BIT W/DSP INT 28-DIP PDF資料下載
參數資料
| 型號： | AD7878JNZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT W/DSP INT 28-DIP |
| 標準包裝： | 1 |
| 位數： | 12 |
| 采樣率（每秒）： | 100k |
| 數據接口： | DSP |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 95.5mW |
| 電壓電源： | 模擬和數字，雙 ± |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 28-DIP（0.600"，15.24mm） |
| 供應商設備封裝： | 28-PDIP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個單端，雙極 |
AD7878
–5–
REV. A
ORDERING GUIDE
Signal-
Data
Temperature
to-Noise
Access
Package
Model
1, 2
Range
Ratio
Time
Options
3
AD7878JN
0
°C to +70°C
70 dB
57 ns
N-28
AD7878AQ
–25
°C to +85°C
70 dB
57 ns
Q-28
AD7878SQ
–55
°C to +125°C
70 dB
57 ns
Q-28
AD7878KN
0
°C to +70°C
72 dB
57 ns
N-28
AD7878BQ
–25
°C to +85°C
72 dB
57 ns
Q-28
AD7878LN
0
°C to +70°C
72 dB
41 ns
N-28
AD7878SE
4
–55
°C to +125°C
70 dB
57 ns
E-28A
AD7878JP
0
°C to +70°C
70 dB
57 ns
P-28A
AD7878KP
0
°C to +70°C
72 dB
57 ns
P-28A
AD7878LP
0
°C to +70°C
72 dB
41 ns
P-28A
NOTES
1To order MIL-STD-883, Class B processed parts, add /883B to part number.
Contact our local sales office for military data sheet.
2Analog Devices reserves the right to ship either ceramic (D-28) packages or
cerdip (Q-28) hermetic packages.
3E = Leadless Ceramic Chip Carrier; N = Plastic DIP; P = Plastic Leaded Chip
Carrier, Q = Cerdip.
4Available to /883B processing only.
STATUS/CONTROL REGISTER
The status/control register serves the dual function of providing
control and monitoring the status of the FIFO memory. This
register is directly accessible through the data bus (DB11–DB0)
with a read or write operation while ADD0 is high. A write
operation to the status/control register provides control for the
ALFL output, bus interface and FIFO counter reset. This is
normally done on power-up initialization. The FIFO memory
address pointer is incremented after each conversion and com-
pared with a preprogrammed count in the status/control regis-
ter. When this preprogrammed count is reached, the
ALFL
output is asserted if the
ENAF control bit is set to zero. This
ALFL can be used to interrupt the microprocessor after any
predetermined number of conversions (between 1 and 8). The
status of the address pointer along with sample overrange and
ALFL status can be accessed at any time by reading the status/
control register. Note: reading the status/control register does
not cause any internal data movement in the FIFO memory.
Status information for a particular word should be read from the
status register before the data word is read from the FIFO
memory.
STATUS/CONTROL REGISTER FUNCTION
DESCRIPTION
DB11 (
ALFL)
Almost Full Flag, Read only. This is the same as Pin 6 (
ALFL
output) status. A logic low indicates that the word count in
the FIFO memory has reached the preprogrammed count in bit
locations DB10–DB8.
ALFL is updated at the end of conversion.
DB10–DB8 (AFC2–AFC0)
Almost Full Word Count, Read/Write. The count value deter-
mines the number of words in the FIFO memory, which will
cause
ALFL to be set. When the FIFO word count equals the
programmed count in these three bits, both the
ALFL output
and DB11 of the status register are set to a logic low. For ex-
ample, when a code of 011 is written to these bits,
ALFL is set
when Location 0 through Location 3 of the FIFO memory
contains valid data. AFC2 is the most significant bit of the word
count. The count value can be read back if required.
DB7 (
ENAF)
Enable Almost Full, Read/Write. Writing a 1 to this bit disables
the
ALFL output and status register bit DB11.
DB6 (FOVR/RESET)
FIFO Overrun/RESET, Read/Write. Reading a 1 from this bit
indicates that at least one sample has been discarded because
the FIFO memory is full. When the FIFO is full (i.e., contains
eight words) any further conversion results will be lost. Writing
a 1 to this bit causes a system RESET as per the
RESET input
(Pin 27).
DB5 (FOOR/DISO)
FIFO Out of RANGE/Disable Outputs, Read/Write. Reading a
1 from this bit indicates that at least one sample in the FIFO
memory is out of range. Writing a 0 to this bit prevents the data
bus from becoming active while
BUSY is low, regardless of the
state of
CS and DMRD.
DB4 (FEMP)
FIFO Empty, Read Only. Reading a 1 indicates there are no
samples in the FIFO memory. When the FIFO is empty the
internal ripple-down effects of the FIFO are disabled and fur-
ther reads will continue to access the last valid data word in
Location 0.
DB3 (SOOR)
Sample out of Range, Read Only. Reading a 1 indicates the next
sample to be read is out of range, i.e., the sample in Location 0
of the FIFO.
DB–DB0 (FCN2–FCN0)
FIFO Word Count, Read Only. The value read from these bits
indicates the number of samples in the FIFO memory. For
example, reading 011 from these bits indicates that Location 0
through Location 3 contains valid data. Note: reading all 0s
indicates there is either one word or no word in the FIFO
memory; in this case the FIFO Empty determines if there is no
word in memory. FCN2 is the most significant bit.
Table I. Status/Control Bit Function Description
BIT LOCATION
DB11
DB10
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
STATUS INFORMATION (READ)
ALFL
AFC2
AFC1
AFC0
ENAF
FOVR
FOOR
FEMP
SOOR
FCN2
FCN1
FCN0
CONTROL FUNCTION (WRITE)
X
AFC2
AFC1
AFC0
ENAF
RESET
DISO
X
XXX
X
RESET STATUS
1
0
1
0
X =DON’T CARE
相關PDF資料 |
PDF描述 |
|---|---|
| IDT72V801L15PFI8 | IC SYNC FIFO 256X9 15NS 64QFP |
| LTC1350ISW | IC TXRX 3.3V EIA/TIA-562 28-SOIC |
| VE-B6F-MW-F4 | CONVERTER MOD DC/DC 72V 100W |
| MS3106R28-11SX | CONN PLUG 22POS STRAIGHT W/SCKT |
| VI-B1Z-MX | CONVERTER MOD DC/DC 2V 30W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7878JP | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 12-bit Parallel 28-Pin PLCC 制造商:Rochester Electronics LLC 功能描述:12-BIT ADC IC - Bulk |
| AD7878JPZ | 功能描述:IC ADC 12BIT W/DSP INT 28-PLCC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| AD7878JPZ-REEL | 功能描述:IC ADC 12BIT W/DSP 28PLCC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7878KN | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 12-bit Parallel 28-Pin PDIP W 制造商:Rochester Electronics LLC 功能描述:COMPLETE 12 BIT ADC IC - Bulk |
| AD7878KP | 制造商:Rochester Electronics LLC 功能描述:12-BIT ADC IC - Bulk 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。