參數資料
型號： AD7888ARUZ-REEL
廠商： Analog Devices Inc
文件頁數： 5/17頁
文件大?。?/td> 0K
描述： IC ADC 12BIT 8CH SRL 16-TSSOP
標準包裝： 2,500
位數： 12
采樣率（每秒）： 125k
數據接口： DSP，MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 1
功率耗散（最大）： 3.5mW
電壓電源： 單電源
工作溫度： -40°C ~ 105°C
安裝類型： 表面貼裝
封裝/外殼： 16-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 16-TSSOP
包裝： 帶卷 (TR)
輸入數目和類型： 8 個單端，單極
AD7888
–13–
SERIAL INTERFACE
Figure 16 shows the detailed timing diagram for serial interfac-
ing to the AD7888. The serial clock provides the conversion
clock and also controls the transfer of information to and from
the AD7888 during conversion.
CS initiates the data transfer and conversion process. For the
autoshutdown mode, the first falling edge of SCLK after the
falling edge of
CS wakes up the part. In all cases, it gates the
serial clock to the AD7888 and puts the on-chip track/hold into
track mode. The input signal is sampled on the second rising
edge of the SCLK input after the falling edge of
CS. Thus, the
first one and one-half clock cycles after the falling edge of
CS is
when the acquisition of the input signal takes place. This time is
denoted as the acquisition time (tACQ). In autoshutdown mode,
the acquisition time must allow for the wake-up time of 5
s. The
on-chip track/hold goes from track mode to hold mode on the
second rising edge of SCLK and a conversion is also initiated on
this edge. The conversion process takes a further fourteen and
one-half SCLK cycles to complete. The rising edge of
CS will
put the bus back into three-state. If
CS is left low a new conver-
sion will be initiated.
The input channel that is sampled is the one selected in the
previous write to the Control Register. Thus, the user must
write ahead of the channel for conversion. In other words, the
user must write the channel address for the next conversion
while the present conversion is in progress.
DONTC
REF
ZERO
ADD2
ADD1
ADD0
PM1
PM0
SCLK
15
6
15
DOUT
DIN
23
4
16
t1
tACQ
tCONVERT
t2
t6
t7
t3
t8
DB11
DB0
DB10
DB9
4 LEADING ZEROS
CS
THREE-
STATE
t4
t5
THREE-
STATE
Figure 16. Serial Interface Timing Diagram
Writing of information to the Control Register takes place on
the first eight rising edges of SCLK in a data transfer. The Con-
trol Register is always written to when a data transfer takes
place. The user must be careful to always set up the correct
information on the DIN line when reading data from the part.
Sixteen serial clock cycles are required to perform the conver-
sion process and to access data from the AD7888. In applica-
tions where the first serial clock edge, following
CS going low, is
a falling edge, this edge clocks out the first leading zero. Thus,
the first rising clock edge on the SCLK clock has the first lead-
ing zero provided. In applications where the first serial clock
edge, following
CS going low, is a rising edge, the first leading
zero may not be set up in time for the processor to read it cor-
rectly. However, subsequent bits are clocked out on the falling
edge of SCLK so they are provided to the processor on the
following rising edge. Thus, the second leading zero is clocked
out on the falling edge subsequent to the first rising edge. The
final bit in the data transfer is valid on the 16th rising edge,
having being clocked out on the previous falling edge.
NOTE: The mark space ratio for SCLK is specified for at least
40% high time (with corresponding 60% low time) or 40% low
time (with corresponding 60% high time). As the SCLK frequency
is reduced, the mark space ratio may vary provided the conver-
sion time never exceeds 50
s—to avoid capacitive droop effects.
REV. C
相關PDF資料
PDF描述
D38999/26FJ61SNLC CONN HSG PLUG 61POS STRGHT SCKT
VE-2N1-CU-S CONVERTER MOD DC/DC 12V 200W
LTC2236IUH#TRPBF IC ADC 10BIT 25MSPS 3V 32-QFN
VE-2N0-CU-S CONVERTER MOD DC/DC 5V 200W
D38999/26WJ61SNLC CONN HSG PLUG 61POS STRGHT SCKT
相關代理商/技術參數
參數描述
AD7888ARUZ-REEL7 功能描述:IC ADC 12BIT SRL 125KSPS 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
AD7888ARZ 功能描述:IC ADC 12BIT 8CH SRL 16-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
AD7888ARZ-REEL 功能描述:IC ADC 12BIT 8CH SRL 16-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:-
AD7888ARZ-REEL7 功能描述:IC ADC 12BIT 8CH SRL 16-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
AD7888BR 制造商:Analog Devices 功能描述:ADC Single SAR 125ksps 12-bit Serial 16-Pin SOIC N
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*