參數資料
型號: AD7889-1ACBZ-RL7
廠商: Analog Devices Inc
文件頁數: 29/41頁
文件大?。?/td> 0K
描述: IC ADC 12BIT CTRLR TOUCH 12WLCSP
產品變化通告: 8mm Carrier Tape Changes 28/Feb/2012
標準包裝: 3,000
類型: 電阻
觸摸面板接口: 4 線
輸入數/鍵: 1 TSC
分辨率(位): 12 b
數據接口: I²C,串行
數據速率/采樣率 (SPS,BPS): 105k
電壓基準: 外部
電源電壓: 1.6 V ~ 3.6 V
電流 - 電源: 10nA
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 12-UFBGA,WLCSP
供應商設備封裝: 12-WLCSP
包裝: 帶卷 (TR)
AD7879/AD7889
Rev. C | Page 34 of 40
07667-
041
DIN
CW
15
CW
14
CW
13
CW
8
CW
1
CW
0
X
SCL
CW
12
X
READBACK DATA FOR
STARTING REGISTER
ADDRESS
X
1
32
2
3
4
15
16
17
18
31
34
33
48
47
49
CS
CW
11
CW
10
CW
9
CW
7
CW
2
CW
6
CW
5
CW
4
CW
3
11
12
13
14
5
6
7
8
9
10
XXX
D15
D14
D1
D0
D1
D0
D15
D14
XXX
XXX XXX
XXX
XXX XXX
XXX
DOUT
16-BIT COMMAND WORD
ENABLE WORD
R/W
STARTING REGISTER ADDRESS
NOTES
1. MULTIPLE SEQUENTIAL REGISTERS CAN BE READ BACK CONTINUOUSLY.
2. THE 16-BIT COMMAND WORD MUST BE WRITTEN ON DIN: 5 BITS FOR ENABLE WORD, 1 BIT FOR R/W, AND 10 BITS FOR REGISTER ADDRESS.
3. THE ADDRESS AUTOMATICALLY INCREMENTS WITH EACH 16-BIT DATA-WORD BEING READ BACK ON THE DOUT PIN.
4. CS IS HELD LOW UNTIL ALL REGISTER BITS HAVE BEEN READ BACK.
5. X DENOTES DON’T CARE.
6. XXX DENOTES HIGH IMPEDANCE THREE-STATE OUTPUT.
7. 16-BIT COMMAND WORD SETTINGS FOR SEQUENTIAL READBACK OPERATION:
CW[15:11] = 11100 (ENABLE WORD)
CW[10] = 1 (R/W)
CW[9:0] = [AD9, AD8, AD7, AD6, AD5, AD4, AD3, AD2, AD1, AD0] (STARTING MSB JUSTIFIED REGISTER ADDRESS)
READBACK DATA FOR
NEXT REGISTER ADDRESS
Figure 42. Sequential Register Readback, SPI Timing
I2C-COMPATIBLE INTERFACE
The AD7879-1/AD7889-1 support the industry standard 2-wire
I2C serial interface protocol. The two wires associated with the
I2C timing are the SCL and SDA inputs. SDA is an I/O pin that
allows both register write and register readback operations. The
AD7879-1/AD7889-1 are always slave devices on the I2C serial
interface bus.
The devices have a 7-bit device address, Address 0101 1XX. The
lower two bits are set by tying the ADD0 and ADD1 pins high or
low. The AD7879-1/AD7889-1 respond when the master device
sends its device address over the bus. The AD7879-1/AD7889-1
cannot initiate data transfers on the bus.
Table 25. I2C Device Addresses for the AD7879-1/AD7889-1
ADD1
ADD0
I2C Address
0
0101 100
0
1
0101 101
1
0
0101 110
1
0101 111
Data Transfer
Data is transferred over the I2C serial interface in 8-bit bytes.
The master initiates a data transfer by establishing a start
condition, defined as a high-to-low transition on the serial data
line, SDA, while the serial clock line, SCL, remains high. This
indicates that an address/data stream follows.
All slave peripherals connected to the serial bus respond to the
start condition and shift in the next eight bits, consisting of a
7-bit address (MSB first) plus a R/W bit that determines the
direction of the data transfer. The peripheral whose address
corresponds to the transmitted address responds by pulling the
data line low during the ninth clock pulse. This is known as the
acknowledge bit. All other devices on the bus then remain idle
while the selected device waits for data to be read from or written
to it. If the R/W bit is a 0, the master writes to the slave device.
If the R/W bit is a 1, the master reads from the slave device.
Data is sent over the serial bus in a sequence of nine clock
pulses (eight bits of data followed by an acknowledge bit from
the slave device). Transitions on the data line must occur during
the low period of the clock signal and remain stable during the
high period because a low-to-high transition when the clock
is high can be interpreted as a stop signal. The number of data
bytes transmitted over the serial bus in a single read or write
operation is limited only by what the master and slave devices
can handle.
When all data bytes are read or written, a stop condition is
established. A stop condition is defined by a low-to-high
transition on SDA while SCL remains high. If the AD7879-1/
AD7889-1 encounter a stop condition, they return to the idle
condition.
相關PDF資料
PDF描述
AD7889ACBZ-RL IC ADC 12BIT CTRLR TOUCH 12WLCSP
AD7889-1ACBZ-RL IC ADC 12BIT CTRLR TOUCH 12WLCSP
VE-BTV-IV-B1 CONVERTER MOD DC/DC 5.8V 150W
VE-BT0-IV-B1 CONVERTER MOD DC/DC 5V 150W
VE-B4H-IV-B1 CONVERTER MOD DC/DC 52V 150W
相關代理商/技術參數
參數描述
AD7889ACBZ-500R7 功能描述:IC ADC 12BIT CTRLR TOUCH 12WLCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率(位):- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS,BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
AD7889ACBZ-RL 功能描述:IC ADC 12BIT CTRLR TOUCH 12WLCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率(位):- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS,BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
AD7890ACHIPS-2 功能描述:Data Acquisition System (DAS) 12 bit 117k SPI Die 制造商:analog devices inc. 系列:- 包裝:管件 零件狀態:上次購買時間 類型:數據采集系統(DAS) 分辨率(位):12 b 采樣率(每秒):117k 數據接口:SPI 電壓源:單電源 電壓 - 電源:5V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:模具 供應商器件封裝:模具 標準包裝:1
AD7890AN-10 功能描述:IC DAS 12BIT 8CH 24-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
AD7890AN-2 功能描述:IC DAS 12BIT 8CH 24-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤