- 您現在的位置：買賣IC網 > PDF目錄10133 > AD7983BCPZ-RL (Analog Devices Inc)IC ADC 16BIT 1.33MSPS 10LFCSP PDF資料下載
參數資料
| 型號： | AD7983BCPZ-RL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 3/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT 1.33MSPS 10LFCSP |
| 標準包裝： | 5,000 |
| 系列： | PulSAR® |
| 位數： | 16 |
| 采樣率（每秒）： | 1.33M |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 12mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-WFDFN 裸露焊盤，CSP |
| 供應商設備封裝： | 10-LFCSP-WD（3x3） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，單極 |
AD7983
Rev. A | Page 11 of 24
TERMINOLOGY
Integral Nonlinearity Error (INL)
INL refers to the deviation of each individual code from a line
drawn from negative full scale through positive full scale. The
point used as negative full scale occurs LSB before the first
code transition. Positive full scale is defined as a level 1 LSB
beyond the last code transition. The deviation is measured from
the middle of each code to the true straight line (see Figure 22).
Differential Nonlinearity Error (DNL)
In an ideal ADC, code transitions are 1 LSB apart. DNL is the
maximum deviation from this ideal value. It is often specified in
terms of resolution for which no missing codes are guaranteed.
Offset Error
The first transition should occur at a level LSB above analog
ground (38.1 μV for the 0 V to 5 V range). The offset error is
the deviation of the actual transition from that point.
Gain Error
The last transition (from 111 … 10 to 111 … 11) should
occur for an analog voltage 1 LSB below the nominal full
scale (4.999886 V for the 0 V to 5 V range). The gain error is
the deviation of the actual level of the last transition from the
ideal level after the offset is adjusted out.
Spurious-Free Dynamic Range (SFDR)
SFDR is the difference, in decibels (dB), between the rms
amplitude of the input signal and the peak spurious signal.
Effective Number of Bits (ENOB)
ENOB is a measurement of the resolution with a sine wave
input. It is related to SINAD as follows:
ENOB = (SINADdB 1.76)/6.02
and is expressed in bits.
Noise-Free Code Resolution
Noise-free code resolution is the number of bits beyond which
it is impossible to distinctly resolve individual codes. It is
calculated as
Noise-Free Code Resolution = log2(2N/Peak-to-Peak Noise)
and is expressed in bits.
Effective Resolution
Effective resolution is calculated as
Effective Resolution = log2(2N/RMS Input Noise)
and is expressed in bits.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first five harmonic
components to the rms value of a full-scale input signal and is
expressed in dB.
Dynamic Range
Dynamic range is the ratio of the rms value of the full scale to
the total rms noise measured with the inputs shorted together.
The value for dynamic range is expressed in dB. It is measured
with a signal at 60 dBFS to include all noise sources and DNL
artifacts.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to the
rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in dB.
Signal-to-(Noise + Distortion) Ratio (SINAD)
SINAD is the ratio of the rms value of the actual input signal to
the rms sum of all other spectral components below the Nyquist
frequency, including harmonics but excluding dc. The value for
SINAD is expressed in dB.
Aperture Delay
Aperture delay is the measurement of the acquisition performance.
It is the time between the rising edge of the CNV input and
when the input signal is held for a conversion.
Transient Response
Transient response is the time required for the ADC to
accurately acquire its input after a full-scale step function is
applied.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1032CSW | IC LINE DRIVR LOWPWR QUAD 16SOIC |
| IDT7202LA25TPI | IC FIFO ASYNCH 1KX9 25NS 28DIP |
| IDT7202LA25JI | IC FIFO ASYNCH 1KX9 25NS 32PLCC |
| LT1785ACS8#TRPBF | IC TXRX 60V RS485/RS422 8SOIC |
| IDT7202LA15SOI8 | IC FIFO ASYNCH 1KX9 15NS 28SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7983BCPZ-RL7 | 功能描述:IC ADC 16BIT 1.33MSPS 10LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7983BRMZ | 功能描述:IC ADC 16BIT 1.33MSPS 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7983BRMZRL7 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 1.33 MSPS PulSAR ADC in MSOP/QFN |
| AD7983BRMZ-RL7 | 功能描述:IC ADC 16BIT 1.33MSPS 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7984 | 制造商:AD 制造商全稱:Analog Devices 功能描述:18-Bit, 1.33 MSPS PulSAR 10.5 mW ADC in MSOP/QFN |
發布緊急采購，3分鐘左右您將得到回復。