參數資料
型號： AD7984BRMZ-RL7
廠商： Analog Devices Inc
文件頁數： 6/24頁
文件大小： 0K
描述： IC ADC 18BIT 1.3MSPS SAR 10MSOP
設計資源： Converting a Single-Ended Signal with AD7984 Differential PulSAR ADC (CN0033)
標準包裝： 1,000
系列： PulSAR®
位數： 18
采樣率（每秒）： 1.33M
數據接口： DSP，MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 1
功率耗散（最大）： 14mW
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 10-TFSOP，10-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 10-MSOP
包裝： 帶卷 (TR)
輸入數目和類型： 1 個差分，單極
AD7984
Rev. A | Page 14 of 24
ANALOG INPUTS
Figure 24 shows an equivalent circuit of the input structure of
the AD7984.
The two diodes, D1 and D2, provide ESD protection for the
analog inputs, IN+ and IN. Care must be taken to ensure that
the analog input signal does not exceed the reference input
voltage (REF) by more than 0.3 V. If the analog input signal
exceeds this level, the diodes become forward-biased and start
conducting current. These diodes can handle a forward-biased
current of 130 mA maximum. However, if the supplies of the
input buffer (for example, the supplies of the ADA4841 in
Figure 23) are different from those of REF, the analog input
signal may eventually exceed the supply rails by more than
0.3 V. In such a case (for example, an input buffer with a short-
circuit), the current limitation can be used to protect the part.
CPIN
REF
RIN
CIN
D1
D2
IN+ OR IN–
GND
06
97
3-
0
1
4
Figure 24. Equivalent Analog Input Circuit
The analog input structure allows the sampling of the true
differential signal between IN+ and IN. By using these
differential inputs, signals common to both inputs are rejected.
90
85
80
75
70
65
60
1
10
100
1000
10000
FREQUENCY (kHz)
CM
RR
(
d
B
)
0
69
73
-01
5
Figure 25. Analog Input CMRR vs. Frequency
During the acquisition phase, the impedance of the analog
inputs (IN+ or IN) can be modeled as a parallel combination
of capacitor, CPIN, and the network formed by the series connection
of RIN and CIN. CPIN is primarily the pin capacitance. RIN is typically
400 Ω and is a lumped component composed of serial resistors
and the on resistance of the switches. CIN is typically 30 pF and
is mainly the ADC sampling capacitor.
During the sampling phase, where the switches are closed, the
input impedance is limited to CPIN. RIN and CIN make a 1-pole,
low-pass filter that reduces undesirable aliasing effects and
limits noise.
When the source impedance of the driving circuit is low, the
AD7984 can be driven directly. Large source impedances
significantly affect the ac performance, especially THD. The
dc performances are less sensitive to the input impedance. The
maximum source impedance depends on the amount of THD
that can be tolerated. The THD degrades as a function of the
source impedance and the maximum input frequency.
DRIVER AMPLIFIER CHOICE
Although the AD7984 is easy to drive, the driver amplifier must
meet the following requirements:
The noise generated by the driver amplifier must be kept as
low as possible to preserve the SNR and transition noise
performance of the AD7984. The noise from the driver is
filtered by the AD7984 analog input circuit’s 1-pole, low-
pass filter made by RIN and CIN or by the external filter, if
one is used. Because the typical noise of the AD7984 is
36.24 μV rms, the SNR degradation due to the amplifier is
+
=
2
)
(
2
π
.24
6
3
36.24
log
20
N
3dB
LOSS
Ne
f
SNR
where:
f–3dB is the input bandwidth, in megahertz, of the AD7984
(10 MHz) or the cutoff frequency of the input filter, if
one is used.
N is the noise gain of the amplifier (for example, 1 in buffer
configuration).
eN is the equivalent input noise voltage of the op amp, in
nV/√Hz.
For ac applications, the driver should have a THD perfor-
mance commensurate with the AD7984.
For multichannel multiplexed applications, the driver
amplifier and the AD7984 analog input circuit must settle
for a full-scale step onto the capacitor array at an 18-bit level
(0.0004%, 4 ppm). In the data sheet of the amplifier,
settling at 0.1% to 0.01% is more commonly specified. This
may differ significantly from the settling time at an 18-bit
level and should be verified prior to driver selection.
Table 8. Recommended Driver Amplifiers
Amplifier
Typical Application
Very low noise, low power single-to-differential
Very low noise, small, and low power
Very low noise and high frequency
Low noise and high frequency
Low power, low noise, and low frequency
5 V single supply, low noise
5 V single supply, low power
相關PDF資料
PDF描述
LT1781IN#PBF IC DVR/RCVR 5V RS232 DUAL 16-DIP
MS3111E14-12P CONN RCPT 12POS CBL MNT W/PINS
VE-2ND-MX-F3 CONVERTER MOD DC/DC 85V 75W
IDT72215LB10PF8 IC FIFO 512X18 SYNC 10NS 64-TQFP
MS27497E14B97P CONN RCPT 12POS WALL MNT W/PINS
相關代理商/技術參數
參數描述
AD7985 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 2.5 MSPS, PulSAR 15.5 mW ADC in LFCSP
AD7985BCPZ 功能描述:IC ADC 16B 2.5MSPS PULSR 20LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD7985BCPZ-RL7 功能描述:IC ADC 16B 2.5MSPS PULSR 20LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD7986 制造商:AD 制造商全稱:Analog Devices 功能描述:1 nV/√Hz, Low Power
AD7986BCPZ 功能描述:IC ADC 18BIT 2MSPS SAR 20LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*