Control of the AD7992 is carried out via the I2
參數資料
型號： AD7992BRMZ-1REEL
廠商： Analog Devices Inc
文件頁數： 14/29頁
文件大?。?/td> 0K
描述： IC ADC 12BIT 2CHAN I2C 10MSOP
標準包裝： 3,000
位數： 12
采樣率（每秒）： 79k
數據接口： I²C，串行
轉換器數目： 1
功率耗散（最大）： 2.2mW
電壓電源： 單電源
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 10-TFSOP，10-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 10-MSOP
包裝： 帶卷 (TR)
輸入數目和類型： 2 個單端，單極
AD7992
Rev. 0 | Page 20 of 28
SERIAL INTERFACE
Control of the AD7992 is carried out via the I2C-compatible
serial bus. The AD7992 is connected to this bus as a slave device
under the control of a master device, such as the processor.
SERIAL BUS ADDRESS
Like all I2C-compatible devices, the AD7992 has a 7-bit serial
address. The 3 MSBs of this address for the AD7992 are set to
010. The device comes in two versions, the AD7992-0 and the
AD7992-1. The two versions have three different I2C addresses
available, which are selected by either tying the address select
pin, AS, to AGND or VDD, or by letting the pin float (refer to
Table 6). By giving different addresses for the two versions, up
to five AD7992 devices can be connected to a single serial bus,
or the addresses can be set to avoid conflicts with other devices
on the bus.
The serial bus protocol operates as follows.
The master initiates data transfer by establishing a START
condition, defined as a high-to-low transition on the serial
data line SDA, while the serial clock line, SCL, remains high.
This indicates that an address/data stream follows. All slave
peripherals connected to the serial bus respond to the START
condition and shift in the next eight bits, consisting of a 7-bit
address (MSB first) plus an R/W bit that determines the
direction of the data transfer—that is, whether data is written to
or read from the slave device.
The peripheral whose address corresponds to the transmitted
address responds by pulling the data line low during the low
period before the ninth clock pulse, known as the acknowledge
bit. All other devices on the bus remain idle while the selected
device waits for data to be read from or written to it. If the R/W
bit is a 0, the master writes to the slave device. If the R/W bit is
a 1, the master reads from the slave device.
Data is sent over the serial bus in sequences of nine clock
pulses, eight bits of data followed by an acknowledge bit from
the receiver of data. Transitions on the data line must occur
during the low period of the clock signal and remain stable
during the high period, because a low-to-high transition when
the clock is high may be interpreted as a STOP signal.
When all data bytes have been read or written, stop conditions
are established. In write mode, the master pulls the data line
high during the 10th clock pulse to assert a STOP condition. In
read mode, the master device pulls the data line high during the
low period before the ninth clock pulse. This is known as no
acknowledge. The master then takes the data line low during
the low period before the 10th clock pulse, then high during the
10th clock pulse to assert a STOP condition.
Any number of bytes of data may be transferred over the serial
bus in one operation, but it is not possible to mix read and write
in one operation because the type of operation is determined at
the beginning and cannot subsequently be changed without
starting a new operation.
相關PDF資料
PDF描述
AD7994BRUZ-1 IC ADC 12BIT 4CHAN I2C 16TSSOP
AD800-52BR IC CLK\DATA RECOVERY PLL 20-SOIC
AD809BR-REEL7 IC SYNTH FREQ 155.52MHZ 16-SOIC
AD8300AR IC DAC 12BIT 3V SRL-IN 8-SOIC
AD8522AR IC DAC 12BIT DUAL 5V 14-SOIC
相關代理商/技術參數
參數描述
AD7993 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP
AD7993-0 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 10- and 12-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP
AD7993-1 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 10- and 12-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP
AD7993BRU 制造商:Analog Devices 功能描述:ADC SGL SAR 188KSPS 10-BIT SERL 16TSSOP - Bulk
AD7993BRU-0 功能描述:IC ADC 10BIT 4CH W/I2C 16-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*