V
參數資料
型號: AD8042AN
廠商: Analog Devices Inc
文件頁數: 8/17頁
文件大?。?/td> 0K
描述: IC OPAMP VF R-R DUAL LP 8DIP
設計資源: Single-Ended-to-Differential Converters for Voltage Output and Current Output DACs Using AD8042 (CN0143)
標準包裝: 50
放大器類型: 電壓反饋
電路數: 2
輸出類型: 滿擺幅
轉換速率: 225 V/µs
-3db帶寬: 170MHz
電流 - 輸入偏壓: 1.2µA
電壓 - 輸入偏移: 3000µV
電流 - 電源: 6mA
電流 - 輸出 / 通道: 50mA
電壓 - 電源,單路/雙路(±): 3 V ~ 12 V,±1.5 V ~ 6 V
工作溫度: -40°C ~ 85°C
安裝類型: 通孔
封裝/外殼: 8-DIP(0.300",7.62mm)
供應商設備封裝: 8-PDIP
包裝: 管件
AD8042
Rev. E | Page 15 of 16
010
59
-0
43
6
5
7
14
10
5
ATT
2718AF
93DJ39
2k
0.001F
0.0027F
0.001F
2k
34
2k
232
2k
3k
VIN
3k
912
249
2
3
1
2
3
1
2
9
7
6
1/4
AD8044
1/2
AD8042
1/2
AD8042
VOUT
VREC
The circuit was tested with a 1 MHz input signal and clocked
at 10 MHz. An FFT response of the digital output is shown in
Pin 5 is biased at 2.5 V by the voltage divider and bypassed.
This biases each output at 2.5 V. VIN is ac-coupled such that
VIN going positive makes VINA go positive and VINB go in
the negative direction. The opposite happens for a negative
going VIN.
V
E
RT
ICAL
S
CAL
E
(1
5d
B/
DI
V
)
HARMONICS (dBc)
FUND FRQ 1000977
THD
–82.00
2ND –88.34
6TH –99.47
SMPL FRQ 10000000 SNR
71.13
3RD –86.74
7TH –91.16
SINAD 70.79
4TH –99.26
8TH –97.25
SFDR
–86.74
5TH –90.67
9TH –91.61
01
05
9-
0
42
1
8
2
7
3
4
6
5
9
Figure 43. HDSL Line Driver
LAYOUT CONSIDERATIONS
The specified high speed performance of the AD8042 requires
careful attention to board layout and component selection.
Proper RF design techniques and low-pass parasitic component
selection are necessary.
The PCB should have a ground plane covering all unused
portions of the component side of the board to provide a low
impedance path. The ground plane should be removed from
the area near the input pins to reduce the stray capacitance.
Figure 42. FFT of the AD9220 Output When Driven by the AD8042
HDSL Line Driver
High bit rate digital subscriber line (HDSL) is a popular means
of providing data communication at DS1 rates (1.544 Mbps)
over moderate distances via conventional telephone twisted pair
wires. In these systems, the transceiver at the customer’s end is
powered sometimes via the twisted pair from a power source at
the central office. Sometimes, it is required to raise the dc voltage
of the power source to compensate for IR drops in long lines or
lines with narrow gauge wires.
Chip capacitors should be used for the supply bypassing. One
end should be connected to the ground plane and the other
within -inch of each power pin. An additional large (0.47 μF
to 10 μF) tantalum electrolytic capacitor should be connected in
parallel, but not necessarily so close to supply current, for fast,
large signal changes at the output.
The feedback resistor should be located close to the inverting
input pin to keep the stray capacitance at this node to a
minimum. Capacitance variations of less than 1 pF at the
inverting input significantly affect high speed performance.
Because of the IR drop, it is highly desirable to keep the power
consumption of the customer’s transceiver as low as possible.
One means to realize significant power savings is to run
the transceiver from a ±5 V supply instead of the more
conventional ±12 V.
Stripline design techniques should be used for long signal
traces (greater than approximately one inch). These should be
designed with a characteristic impedance of 50 Ω or 75 Ω and
be properly terminated at each end.
The high output swing and current drive capability of the
AD8042 make it ideally suited to this application. Figure 43
shows a circuit for the analog portion of an HDSL transceiver
using the AD8042 as the line driver.
相關PDF資料
PDF描述
Y16361K00000T9W RES 1K OHM .1W .01% FOIL 0603
Y16070R50000F9W RES .5 OHM .5W 1% FOIL SMD
TMM-144-01-S-S-SM CONN HEADER 44POS SNGL 2MM SMD
LT1228CS8 IC CURRNT FEEDBK AMP 100MHZ8SOIC
170M3415 FUSE 200A 690V 1BN/50 AR UC
相關代理商/技術參數
參數描述
AD8042AR 功能描述:IC OPAMP VF R-R DUAL LP 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:13 V/µs 增益帶寬積:3MHz -3db帶寬:- 電流 - 輸入偏壓:65pA 電壓 - 輸入偏移:3000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:- 電壓 - 電源,單路/雙路(±):7 V ~ 36 V,±3.5 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:8-DIP(0.300",7.62mm) 供應商設備封裝:8-PDIP 包裝:管件
AD8042AR-EBZ 功能描述:BOARD EVAL FOR AD8042AR RoHS:是 類別:編程器,開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:-
AD8042AR-REEL 功能描述:IC OPAMP VF R-R DUAL LP 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:2.1 V/µs 增益帶寬積:3MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:2000µV 電流 - 電源:750µA 電流 - 輸出 / 通道:16mA 電壓 - 電源,單路/雙路(±):2.7 V ~ 16 V,±1.35 V ~ 8 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC(0.154",3.90mm 寬) 供應商設備封裝:14-SOIC 包裝:剪切帶 (CT) 其它名稱:296-10529-1
AD8042AR-REEL7 功能描述:IC OPAMP VF R-R DUAL LP 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源,單路/雙路(±):7 V ~ 36 V,±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP(0.300",7.62mm) 供應商設備封裝:8-PDIP 包裝:管件
AD8042ARZ 功能描述:IC OPAMP VF R-R DUAL LP 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源,單路/雙路(±):3 V ~ 32 V,±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR