參數資料
型號: AD8131ARM
廠商: Analog Devices Inc
文件頁數: 11/21頁
文件大?。?/td> 0K
描述: IC AMP DIFF LDIST 60MA 8MSOP
標準包裝: 50
放大器類型: 差分
電路數: 1
輸出類型: 差分
轉換速率: 2000 V/µs
-3db帶寬: 400MHz
電流 - 輸入偏壓: 500nA
電壓 - 輸入偏移: 1500µV
電流 - 電源: 11.5mA
電流 - 輸出 / 通道: 60mA
電壓 - 電源,單路/雙路(±): 2.8 V ~ 11 V,±1.4 V ~ 5.5 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 8-TSSOP,8-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 8-MSOP
包裝: 管件
AD8131
Rev. B | Page 18 of 20
APPLICATIONS
TWISTED-PAIR LINE DRIVER
The AD8131 has on-chip resistors that provide for a gain of 2
without any external parts. Several on-chip resistors are
trimmed to ensure that the gain is accurate, the common-mode
rejection is good, and the output is well balanced. This makes
the AD8131 very suitable as a single-ended-to-differential
twisted-pair line driver.
Figure 40 shows a circuit of an AD8131 driving a twisted-pair
line, like a Category 3 or Category 5 (Cat3 or Cat5), that is
already installed in many buildings for telephony and data
communications. The characteristic impedance of such a
transmission line is usually about 100 Ω. The outstanding
balance of the AD8131 output will minimize the common-
mode signal and therefore the amount of EMI generated by
driving the twisted pair.
The two resistors in series with each output terminate the line at
the transmit end. Since the impedances of the outputs of the
AD8131 are very low, they can be thought of as a short-circuit,
and the two terminating resistors form a 100 Ω termination at
the transmit end of the transmission line. The receive end is
directly terminated by a 100 Ω resistor across the line.
This back-termination of the transmission line divides the
output signal by two. The fixed gain of 2 of the AD8131 will
create a net unity gain for the system from end to end.
In this case, the input signal is provided by a signal generator
with an output impedance of 50 Ω. This is terminated with a
49.9 Ω resistor near +DIN of the AD8131. The effective parallel
resistance of the source and termination is 25 Ω.The 24.9 Ω
resistor from DIN to ground matches the +DIN source
impedance and minimizes any dc and gain errors.
If +DIN is driven by a low-impedance source over a short
distance, such as the output of an op amp, then no termination
resistor is required at +DIN. In this case, the DIN can be directly
tied to ground.
AD8131
8
2
3
6
5
4
+
1
24.9
Ω
49.9
Ω
100
Ω
10
μF
0.1
μF
49.9
Ω
49.9
Ω
10
μF
0.1
μF
+5V
–5V
RECEIVER
01072-040
Figure 40. Single-Ended-to-Differential 100 Ω Line Driver
3 V SUPPLY DIFFERENTIAL A-TO-D DRIVER
Many newer ADCs can run from a single 3 V supply, which can
save significant system power. In order to increase the dynamic
range at the analog input, they have differential inputs, which
double the dynamic range with respect to a single-ended input.
An added benefit of using a differential input is that the
distortion can be improved.
The low distortion and ability to run from a single 3 V supply make
the AD8131 suited as an A-to-D driver for some 10-bit, single-
supply applications. Figure 41 shows a schematic for a circuit for an
AD8131 driving an AD9203, a 10-bit, 40 MSPS ADC.
The common mode of the AD8131 output is set at midsupply
by the voltage divider connected to VOCM, and ac-bypassed with
a 0.1 μF capacitor. This provides for maximum dynamic range
between the supplies at the output of the AD8131. The 110 Ω
resistors at the AD8131 output, along with the shunt capacitors
form a one pole, low-pass filter for lowering noise and
antialiasing.
AD8131
8
2
3
6
+
3V
LPF
+3V
1
20pF
AD9203
26
25
28
AVDD
DRVDD
AINP
AINN
AVSS
DRVSS
3V
27
1
2
DIGITAL
OUTPUTS
0.1 F
10 F
0.1 F
110
Ω
110
Ω
24.9
Ω
49.9
Ω
10k
Ω
10k
Ω
VOCM
01072-041
Figure 41. Test Circuit for AD8131 Driving an AD9203, 10-Bit, 40 MSPS ADC
Figure 42 shows an FFT plot that was taken from the combined
devices at an analog input frequency of 2.5 MHz and a 40 MSPS
sampling rate. The performance of the AD8131 compares very
favorably with a center-tapped transformer drive, which has
typically been the best way to drive this ADC. The AD8131 has
the advantage of maintaining dc performance, which a
transformer solution cannot provide.
相關PDF資料
PDF描述
TMM-121-01-G-D-SM CONN HEADER 42POS DUAL 2MM SMD
SL1021B420RF GAS TUBE GDT 10KA 420V RAD +FS
TSW-149-07-G-D CONN HEADER 98POS .100" DL GOLD
929715-10-29-I CONN HEADER .100 DUAL STR 58POS
SL1021B500RF GAS TUBE 500V HVY 10KA 3PIN RADL
相關代理商/技術參數
參數描述
AD8131ARM-EBZ 功能描述:BOARD EVAL FOR AD8131ARM RoHS:是 類別:編程器,開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:-
AD8131ARM-REEL 制造商:Analog Devices 功能描述:SP Amp DIFF Line Driver Amp Single 制造商:Analog Devices 功能描述:SP Amp DIFF Line Driver Amp Single ±5.5V/11V 8-Pin MSOP T/R 制造商:Rochester Electronics LLC 功能描述:MINISO LOCOST HI-SPD DIFFERENTIAL DRIVER - Tape and Reel
AD8131ARM-REEL7 功能描述:IC AMP DIFF LDIST 60MA 8MSOP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.11 V/µs 增益帶寬積:350kHz -3db帶寬:- 電流 - 輸入偏壓:4nA 電壓 - 輸入偏移:20µV 電流 - 電源:260µA 電流 - 輸出 / 通道:20mA 電壓 - 電源,單路/雙路(±):2.7 V ~ 36 V,±1.35 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC(0.154",3.90mm 寬) 供應商設備封裝:8-SO 包裝:帶卷 (TR)
AD8131ARMZ 功能描述:IC AMP DIFF LDIST 60MA 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源,單路/雙路(±):3 V ~ 32 V,±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR
AD8131ARMZ 制造商:Analog Devices 功能描述:IC DIFF AMP 400MHZ 2000V/US 8MSOP