參數資料
型號: AD8131ARM
廠商: Analog Devices Inc
文件頁數: 9/21頁
文件大?。?/td> 0K
描述: IC AMP DIFF LDIST 60MA 8MSOP
標準包裝: 50
放大器類型: 差分
電路數: 1
輸出類型: 差分
轉換速率: 2000 V/µs
-3db帶寬: 400MHz
電流 - 輸入偏壓: 500nA
電壓 - 輸入偏移: 1500µV
電流 - 電源: 11.5mA
電流 - 輸出 / 通道: 60mA
電壓 - 電源,單路/雙路(±): 2.8 V ~ 11 V,±1.4 V ~ 5.5 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 8-TSSOP,8-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 8-MSOP
包裝: 管件
AD8131
Rev. B | Page 16 of 20
THEORY OF OPERATION
The AD8131 differs from conventional op amps in that it has
two outputs whose voltages move in opposite directions. Like
an op amp, it relies on high open-loop gain and negative
feedback to force these outputs to the desired voltages. The
AD8131 behaves much like a standard voltage feedback op amp
and makes it easy to perform single-ended-to-differential
conversion, common-mode level-shifting, and amplification of
differential signals.
Previous discrete and integrated differential driver designs used
two independent amplifiers and two independent feedback
loops, one to control each of the outputs. When these circuits
are driven from a single-ended source, the resulting outputs are
typically not well balanced. Achieving a balanced output
typically required exceptional matching of the amplifiers and
feedback networks.
DC common-mode level shifting has also been difficult with
previous differential drivers. Level shifting required the use of a
third amplifier and feedback loop to control the output
common-mode level. Sometimes the third amplifier has also
been used to attempt to correct an inherently unbalanced
circuit. Excellent performance over a wide frequency range has
proven difficult with this approach.
The AD8131 uses two feedback loops to separately control the
differential and common-mode output voltages. The differential
feedback, set by internal resistors, controls only the differential
output voltage. The common-mode feedback controls only the
common-mode output voltage. This architecture makes it easy
to arbitrarily set the common-mode output level. It is forced, by
internal common-mode feedback, to be equal to the voltage
applied to the VOCM input, without affecting the differential
output voltage.
The AD8131 architecture results in outputs that are very highly
balanced over a wide frequency range without requiring
external components or adjustments. The common-mode
feedback loop forces the signal component of the output
common-mode voltage to be zeroed. The result is nearly
perfectly balanced differential outputs, of identical amplitude
and exactly 180 degrees apart in phase.
ANALYZING AN APPLICATION CIRCUIT
The AD8131 uses high open-loop gain and negative feedback to
force its differential and common-mode output voltages in such
a way as to minimize the differential and common-mode error
voltages. The differential error voltage is defined as the voltage
between the differential inputs labeled +IN and IN in
Figure 39. For most purposes, this voltage can be assumed to be
zero. Similarly, the difference between the actual output
common-mode voltage and the voltage applied to VOCM can also
be assumed to be zero. Starting from these two assumptions,
any application circuit can be analyzed.
CLOSED-LOOP GAIN
The differential mode gain of the circuit in Figure 39 can be
described by the following equation:
2
=
G
F
dm
IN,
dm
OUT,
R
V
where RF = 1.5 kΩ and RG = 750 Ω nominally.
ESTIMATING THE OUTPUT NOISE VOLTAGE
Similar to the case of a conventional op amp, the differential
output errors (noise and offset voltages) can be estimated by
multiplying the input referred terms, at +IN and IN, by the
circuit noise gain. The noise gain is defined as
3
1
=
+
=
G
F
N
R
G
The total output referred noise for the AD8131, including the
contributions of RF, RG, and op amp, is nominally 25 nV/√Hz
at 20 MHz.
CALCULATING THE INPUT IMPEDANCE OF AN
APPLICATION CIRCUIT
The effective input impedance of a circuit such as that in
Figure 39, at +DIN and DIN, will depend on whether the
amplifier is being driven by a single-ended or differential signal
source. For balanced differential input signals, the input
impedance (RIN, dm) between the inputs (+DIN and DIN) is
Ω
=
×
=
k
5
.
1
2
,
G
dm
IN
R
In the case of a single-ended input signal (for example if DIN is
grounded and the input signal is applied to +DIN), the input
impedance becomes
()
Ω
=
+
×
=
k
125
.
1
2
1
,
F
G
F
G
dm
IN
R
The input impedance is effectively higher than it would be for a
conventional op amp connected as an inverter because a
fraction of the differential output voltage appears at the inputs
as a common-mode signal, partially bootstrapping the voltage
across the input resistor RG.
相關PDF資料
PDF描述
TMM-121-01-G-D-SM CONN HEADER 42POS DUAL 2MM SMD
SL1021B420RF GAS TUBE GDT 10KA 420V RAD +FS
TSW-149-07-G-D CONN HEADER 98POS .100" DL GOLD
929715-10-29-I CONN HEADER .100 DUAL STR 58POS
SL1021B500RF GAS TUBE 500V HVY 10KA 3PIN RADL
相關代理商/技術參數
參數描述
AD8131ARM-EBZ 功能描述:BOARD EVAL FOR AD8131ARM RoHS:是 類別:編程器,開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:-
AD8131ARM-REEL 制造商:Analog Devices 功能描述:SP Amp DIFF Line Driver Amp Single 制造商:Analog Devices 功能描述:SP Amp DIFF Line Driver Amp Single ±5.5V/11V 8-Pin MSOP T/R 制造商:Rochester Electronics LLC 功能描述:MINISO LOCOST HI-SPD DIFFERENTIAL DRIVER - Tape and Reel
AD8131ARM-REEL7 功能描述:IC AMP DIFF LDIST 60MA 8MSOP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.11 V/µs 增益帶寬積:350kHz -3db帶寬:- 電流 - 輸入偏壓:4nA 電壓 - 輸入偏移:20µV 電流 - 電源:260µA 電流 - 輸出 / 通道:20mA 電壓 - 電源,單路/雙路(±):2.7 V ~ 36 V,±1.35 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC(0.154",3.90mm 寬) 供應商設備封裝:8-SO 包裝:帶卷 (TR)
AD8131ARMZ 功能描述:IC AMP DIFF LDIST 60MA 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源,單路/雙路(±):3 V ~ 32 V,±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR
AD8131ARMZ 制造商:Analog Devices 功能描述:IC DIFF AMP 400MHZ 2000V/US 8MSOP