- 您現在的位置：買賣IC網 > PDF目錄8606 > AD8334ACPZ-REEL (Analog Devices Inc)IC VGA QUAD W/PREAMP 64-LFCSP PDF資料下載
參數資料
| 型號： | AD8334ACPZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 43/56頁 |
| 文件大小： | 0K |
| 描述： | IC VGA QUAD W/PREAMP 64-LFCSP |
| 標準包裝： | 2,500 |
| 系列： | X-AMP® |
| 類型： | 可變增益放大器 |
| 應用： | 信號處理 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 64-LFCSP-VQ（9x9） |
| 包裝： | 帶卷 (TR) |
| 配用： | AD8334-EVALZ-ND - BOARD EVALUATION FOR AD8334 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
AD8331/AD8332/AD8334
Rev. G | Page 48 of 56
CONFIGURING THE INPUT IMPEDANCE
The board is built and tested using the components shown in
black in Figure 115. Provisions are made for optional components
(shown in gray) that can be installed at user discretion. As
shipped, the input impedances of the low noise amplifiers (LNAs)
are configured for 50 Ω to match the output impedances of most
signal generators and network analyzers. Input impedances up to
6 kΩ can be realized by changing the values of the feedback
resistors, RFB1, RFB2, RFB3, RFB4, and shunt capacitors, C6, C8, C10,
and C12. For reference, Table 12 lists standard values of 1%
resistors for some typical values of input impedance. Of course,
if the user has determined that the source impedance falls
between these values, the feedback resistor value can be
calculated accordingly. Note that the board is designed to accept
standard surface-mount, size 0603 components.
Table 12. LNA External Component Values for Common
Source Impedances
RIN (Ω)
RFB1, RFB2, RFB3, RFB4 (Ω, ±1%)
C6, C8, C10, C12 (pF)
50
274
22
75
412
12
100
562
8
200
1.13 k
1.2
500
3.01 k
No capacitor
6 k
No resistor
No capacitor
Driving the VGA from an External Source or Using the
LNA to Drive an External Load
Appropriate components can be installed if the user wants to
drive the VGA directly from an external source or to evaluate
the LNA output. If the LNA is used to drive off-board loads
or cables, small value series resistors (47 Ω to 100 Ω) are
recommended for LNA decoupling. These can be installed
in the R10, R11, R14, R15, R18, R19, R22, and R23 spaces.
Provisions are made for surface-mount SMA connectors that
can be used for driving from either direction. If the LNA is not
used, it is recommended that the capacitors, C16, C17, C21,
C22, C26, C27, C31, and C32, be carefully removed to avoid
driving the outputs of the LNAs.
Using the Clamp Circuit
The board is shipped with no resistors installed in the spaces
provided for clamp-circuit operation. Note that each pair of
channels shares a clamp resistor. If the output clamping is
desired, the resistors are installed in R49 and R50. The peak-to-
peak clamping level is application dependent.
Viewing Signals
The preferred signal detector is a high impedance differential
probe, such as the Tektronix P6247, 1 GHz differential probe,
connected to the 2-pin headers (VO1, VO2, VO3, or VO4), as
shown in Figure 116. The low capacitance of this probe has the
least effect on the performance of the device of any detection
method tried. The probe can also be used for monitoring input
signals at IN1, IN2, IN3, or IN4. It can be used for probing
other circuit nodes; however, be aware that the 200 kΩ input
impedance can affect certain circuits.
Differential-to-single-ended transformers are provided for
single-ended output connections. Note that series resistors are
provided to protect against accidental output overload should a
50 Ω load be connected to the connector. Of course, the effect
of these resistors is to limit the bandwidth. If the load connected
to the SMA is >500 Ω, the 237 Ω series resistors, RX1, RX2, RX3,
RX4, RX5, RX6, RX7, and RX8, can be replaced with 0 Ω values.
03
19
9-
1
23
Figure 114. AD8334-EVALZ Assembly
MEASUREMENT SETUP
The basic board connections for measuring bandwidth are
shown in Figure 116. A 5 V, 200 mA (minimum) power supply
is required, and a low noise voltage reference supply is required
for VGAIN.
BOARD LAYOUT
The evaluation board circuitry uses four conductor layers. The
two inner layers are ground, and all interconnecting circuitry is
located on the outer layers. Figure 117 to Figure 120 illustrate
the copper patterns.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-24K-IV-F4 | CONVERTER MOD DC/DC 40V 150W |
| AD8304ARU-REEL7 | IC LOGARITHMIC CONV 14-TSSOP T/R |
| VI-24K-IV-F3 | CONVERTER MOD DC/DC 40V 150W |
| AD8332ACPZ-R2 | IC AMP VGA PREAMP PROGR 32-LFCSP |
| AD7545LPZ-REEL | IC DAC 12BIT MULT CMOS 20-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8334ACPZ-REEL7 | 功能描述:IC VGA QUAD W/PREAMP 64-LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:X-AMP® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤 |
| AD8334ACPZ-WP | 制造商:Analog Devices 功能描述:SP Amp Variable Gain Amp Quad 5.5V 64-Pin LFCSP EP Tray 制造商:Analog Devices 功能描述:AMP QUAD VARIABLE GAIN LFCSP-64 |
| AD8334-EVAL | 制造商:Analog Devices 功能描述:EVALUATION BOARD QUAD VGA AND ULTRALOW NOISE PREAMPLIFIER WITH PROGRAMMABLE RIN EVALUATION BOARD |
| AD8334-EVALZ | 功能描述:BOARD EVALUATION FOR AD8334 RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:X-AMP® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| AD8335 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad Low Noise, Low Cost Variable Gain Amplifier |
發布緊急采購，3分鐘左右您將得到回復。