參數資料
型號： AD9204BCPZRL7-40
廠商： Analog Devices Inc
文件頁數： 19/36頁
文件大?。?/td> 0K
描述： IC ADC 10BIT 40MSPS 64LFCSP
標準包裝： 750
位數： 10
采樣率（每秒）： 40M
數據接口： 串行，SPI?
轉換器數目： 2
功率耗散（最大）： 97.7mW
電壓電源： 模擬和數字
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 64-VFQFN 裸露焊盤，CSP
供應商設備封裝： 64-LFCSP-VQ（9x9）
包裝： 帶卷 (TR)
輸入數目和類型： 4 個單端，單極；2 個差分，單極
AD9204
Rev. 0 | Page 26 of 36
The AD9204 is placed in power-down mode either by the SPI
port or by asserting the PDWN pin high. In this state, the ADC
typically dissipates 2.2 mW. During power-down, the output
drivers are placed in a high impedance state. Asserting the
PDWN pin low returns the AD9204 to its normal operating
mode. Note that PDWN is referenced to the digital output
driver supply (DRVDD) and should not exceed that supply
voltage.
Low power dissipation in power-down mode is achieved by
shutting down the reference, reference buffer, biasing networks,
and clock. Internal capacitors are discharged when entering power-
down mode and then must be recharged when returning to normal
operation. As a result, wake-up time is related to the time spent
in power-down mode, and shorter power-down cycles result in
proportionally shorter wake-up times.
When using the SPI port interface, the user can place the ADC
in power-down mode or standby mode. Standby mode allows
the user to keep the internal reference circuitry powered when
faster wake-up times are required. See the Memory Map section
for more details.
DIGITAL OUTPUTS
The AD9204 output drivers can be configured to interface with
1.8 V to 3.3 V CMOS logic families. Output data can also be
multiplexed onto a single output bus to reduce the total number of
traces required.
The CMOS output drivers are sized to provide sufficient output
current to drive a wide variety of logic families. However, large
drive currents tend to cause current glitches on the supplies that
may affect converter performance.
Applications requiring the ADC to drive large capacitive loads
or large fanouts may require external buffers or latches.
The output data format can be selected to be either offset binary
or twos complement by setting the SCLK/DFS pin when operating
in the external pin mode (see Table 12).
As detailed in the AN-877 Application Note, Interfacing to High
Speed ADCs via SPI, the data format can be selected for offset
binary, twos complement, or gray code when using the SPI control.
Table 12. SCLK/DFS Mode Selection (External Pin Mode)
Voltage at Pin
SCLK/DFS
SDIO/DCS
AGND
Offset binary (default)
DCS disabled
DRVDD
Twos complement
DCS enabled (default)
Digital Output Enable Function (OEB)
The AD9204 has a flexible three-state ability for the digital
output pins. The three-state mode is enabled using the OEB
pin or through the SPI interface. If the OEB pin is low, the
output data drivers and DCOs are enabled. If the OEB pin is
high, the output data drivers and DCOs are placed in a high
impedance state. This OEB function is not intended for rapid
access to the data bus. Note that OEB is referenced to the digital
output driver supply (DRVDD) and should not exceed that
supply voltage.
When using the SPI interface, the data outputs and DCO of
each channel can be independently three-stated by using the
output disable (OEB) bit (Bit 4) in Register 0x14.
TIMING
The AD9204 provides latched data with a pipeline delay of
nine clock cycles. Data outputs are available one propagation
delay (tPD) after the rising edge of the clock signal.
Minimize the length of the output data lines and loads placed
on them to reduce transients within the AD9204. These
transients can degrade converter dynamic performance.
The lowest typical conversion rate of the AD9204 is 3 MSPS. At
clock rates below 3 MSPS, dynamic performance can degrade.
Data Clock Output (DCO)
The AD9204 provides two data clock output (DCO) signals
intended for capturing the data in an external register. The CMOS
data outputs are valid on the rising edge of DCO, unless the DCO
clock polarity has been changed via the SPI. See Figure 2 and
Figure 3 for a graphical timing description.
Table 13. Output Data Format
Input (V)
Condition (V)
Offset Binary Output Mode
Twos Complement Mode
OR
VIN+ VIN
< VREF 0.5 LSB
00 0000 0000 0000
10 0000 0000 0000
1
VIN+ VIN
= VREF
00 0000 0000 0000
10 0000 0000 0000
0
VIN+ VIN
= 0
10 0000 0000 0000
00 0000 0000 0000
0
VIN+ VIN
= +VREF 1.0 LSB
11 1111 1111 1111
01 1111 1111 1111
0
VIN+ VIN
> +VREF 0.5 LSB
11 1111 1111 1111
01 1111 1111 1111
1
相關PDF資料
PDF描述
VE-23F-CU-F3 CONVERTER MOD DC/DC 72V 200W
FSA221L10X IC SWITCH AUDIO DPDT 10-MICROPAK
AD7938BCPZ-REEL7 IC ADC 12BIT 8CH 1.5MSPS 32LFCSP
VE-B6M-MY CONVERTER MOD DC/DC 10V 50W
VE-23F-CU-F2 CONVERTER MOD DC/DC 72V 200W
相關代理商/技術參數
參數描述
AD9204BCPZRL7-65 功能描述:IC ADC 10BIT 65MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極
AD9204BCPZRL7-80 功能描述:IC ADC 10BIT 80MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極
AD9208BBPZRL-3000
AD9211 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 200 MSPS/250 MSPS/300 MSPS, 1.8 V Analog-to-Digital Converter
AD9211_07 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 200 MSPS/250 MSPS/300 MSPS, 1.8 V Analog-to-Digital Converter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*