- 您現在的位置：買賣IC網 > PDF目錄1986 > AD9284BCPZRL7-250 (Analog Devices Inc)IC ADC 8BIT 250MSPS 1.8V 48LFCSP PDF資料下載
參數資料
| 型號： | AD9284BCPZRL7-250 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 8/24頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 8BIT 250MSPS 1.8V 48LFCSP |
| 標準包裝： | 750 |
| 位數： | 8 |
| 采樣率（每秒）： | 250M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 330mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 48-LFCSP-VQ（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個差分，雙極 |
| 配用： | AD9284-250EBZ-ND - BOARD EVAL FOR AD9284 |
AD9284
Data Sheet
Rev. A | Page 16 of 24
SERIAL PORT INTERFACE (SPI)
The AD9284 serial port interface (SPI) allows the user to configure
the converter for specific functions or operations through a
structured register space provided inside the ADC. The SPI
gives the user added flexibility and customization, depending
on the application. Addresses are accessed via the serial port
and can be written to or read from via the port. Memory is
organized into bytes that can be further divided into fields,
which are documented in the Memory Map section. For detailed
operational information, see the AN-877 Application Note,
Interfacing to High Speed ADCs via SPI.
CONFIGURATION USING THE SPI
Three pins define the SPI of this ADC: SCLK, SDIO, and CSB
(see Table 9). SCLK (a serial clock) is used to synchronize the
read and write data presented from and to the ADC. SDIO
(serial data input/output) is a dual-purpose pin that allows data
to be sent to and read from the internal ADC memory map
registers. CSB (chip select bar) is an active low control that
enables or disables the read and write cycles.
Table 9. Serial Port Interface Pins
Pin
Function
SCLK
Serial clock. A serial shift clock input that is used to
synchronize serial interface reads and writes.
SDIO
Serial data input/output. A dual-purpose pin that
typically serves as an input or an output, depending
on the instruction being sent and the relative position
in the timing frame.
CSB
Chip select bar. An active low control that gates the
read and write cycles.
The falling edge of CSB, in conjunction with the rising edge of
SCLK, determines the start of the framing. An example of the
serial timing and its definitions can be found in Figure 25.
Other modes involving CSB are available. The CSB pin can be
held low indefinitely, which permanently enables the device;
this is called streaming. CSB can stall high between bytes to
allow for additional external timing. When the CSB pin is tied
high, SPI functions are placed in high impedance mode. This
mode turns on any SPI pin secondary functions.
During the instruction phase, a 16-bit instruction is transmitted.
Data follows the instruction phase, and its length is determined
by the W0 and W1 bits, as shown in Figure 25.
All data is composed of 8-bit words. The first bit of the first byte
in a multibyte serial data transfer frame indicates whether a read
command or a write command is issued. This allows the serial
data input/output (SDIO) pin to change direction from an input
to an output at the appropriate point in the serial frame.
In addition to word length, the instruction phase determines
whether the serial frame is a read or write operation, allowing
the serial port to be used both to program the chip and to read
the contents of the on-chip memory. If the instruction is a readback
operation, the serial data input/output (SDIO) pin changes
direction, from an input to an output, at the appropriate point in
the serial frame.
Data can be sent in MSB-first mode or in LSB-first mode. MSB
first is the default on power-up and can be changed via the SPI
port configuration register. For more information about this
and other features, see the AN-877 Application Note, Interfacing
to High Speed ADCs via SPI.
DON’T CARE
SDIO
SCLK
CSB
tS
tDH
tCLK
tDS
tH
R/W
W1
W0
A12
A11
A10
A9
A8
A7
D5
D4
D3
D2
D1
D0
tLOW
tHIGH
090
85-
00
4
Figure 25. Serial Port Interface Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| AD9286BCPZRL7-500 | IC ADC 8BIT SPI/SRL 500M 48LFCSP |
| AD9287BCPZRL7-100 | IC ADC 8BIT QUAD 100MSPS 48LFCSP |
| AD9288BSTZ-100 | IC ADC 8BIT DUAL 100MSPS 48-LQFP |
| AD9289BBC | IC ADC 8BIT QUAD 65MSPS 64CSPBGA |
| AD9410BSVZ | IC ADC 10BIT 210MSPS 80-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9286 | 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Bit, 500 MSPS, 1.8 V Analog-to-Digital Converter (ADC) |
| AD9286-500EBZ | 功能描述:BOARD EVAL FOR AD9286-500 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| AD9286BCPZ-500 | 功能描述:IC ADC 8BIT SPI/SRL 500M 48LFSCP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD9286BCPZRL7-500 | 功能描述:IC ADC 8BIT SPI/SRL 500M 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD9287 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad, 8-Bit, 100 MSPS Serial LVDS 1.8 V A/D Converter |
發布緊急采購，3分鐘左右您將得到回復。