參數資料
型號： AD9640-80EBZ
廠商： Analog Devices Inc
文件頁數： 27/52頁
文件大?。?/td> 0K
描述： ADC 14BIT 80MSPS DUAL 64-LFCSP
設計資源： Interfacing ADL5534 to AD9640 High Speed ADC (CN0049)
AD9640 Eval Brd Family Gerber Files
AD9640 Eval Brd BOM
AD9640 Eval Brd Schematic
標準包裝： 1
ADC 的數量： 2
位數： 14
采樣率（每秒）： 80M
數據接口： 串行
輸入范圍： 2 Vpp
在以下條件下的電源（標準）： 550mW @ 80MSPS
工作溫度： -40°C ~ 85°C
已用 IC / 零件： AD9640
已供物品： 板
AD9640
Rev. B | Page 33 of 52
When the fast detect mode select bits are set to 0b001, 0b010, or
0b011, a subset of the fast detect output pins is available. In these
modes, the fast detect output pins have a latency of six clock cycles.
Table 19 shows the corresponding ADC input levels when the
fast detect mode select bits are set to 0b001 (that is, when ADC fast
magnitude is presented on the FD[3:1] pins).
Table 19. ADC Fast Magnitude Nominal Levels with
Fast Detect Mode Select Bits = 001
ADC Fast Magnitude
on FD[3:1] Pins
Nominal Input
Magnitude
Below FS (dB)
Nominal Input
Magnitude
Uncertainty (dB)
000
<24
Minimum to 18.07
001
24 to 14.5
30.14 to 12.04
010
14.5 to 10
18.07 to 8.52
011
10 to 7
12.04 to 6.02
100
7 to 5
8.52 to 4.08
101
5 to 3.25
6.02 to 2.5
110
3.25 to 1.8
4.08 to 1.16
111
1.8 to 0
2.5 to 0
When the fast detect mode select bits are set to 0b010 or 0b011
(that is, when ADC fast magnitude is presented on the FD[3:2]
pins), the LSB is not provided. The input ranges for this mode
are shown in Table 20.
Table 20. ADC Fast Magnitude Nominal Levels with
Fast Detect Mode Select Bits = 010 or 011
ADC Fast
Magnitude on
FD[2:1] Pins
Nominal Input
Magnitude
Below FS (dB)
Nominal Input
Magnitude
Uncertainty (dB)
00
<14.5
Minimum to 12.04
01
14.5 to 7
18.07 to 6.02
10
7 to 3.25
8.52 to 2.5
11
3.25 to 0
4.08 to 0
ADC OVERRANGE (OR)
The ADC overrange indicator is asserted when an overrange is
detected on the input of the ADC. The overrange condition is
determined at the output of the ADC pipeline and, therefore, is
subject to a latency of 12 ADC clock cycles. An overrange at the
input is indicated by this bit 12 clock cycles after it occurs.
GAIN SWITCHING
The AD9640 includes circuitry that is useful in applications either
where large dynamic ranges exist or where gain ranging converters
are employed. This circuitry allows digital thresholds to be set
such that an upper threshold and a lower threshold can be
programmed. Fast detect mode select bit = 010 through fast
detect mode select bit = 101 support various combinations of the
gain switching options.
One such use is to detect when an ADC is about to reach full
scale with a particular input condition. The result is to provide
an indicator that can be used to quickly insert an attenuator that
prevents ADC overdrive.
Coarse Upper Threshold (C_UT)
The coarse upper threshold indicator is asserted if the ADC fast
magnitude input level is greater than the level programmed in
the coarse upper threshold register (Address 0x105[2:0]). The
coarse upper threshold output is output two clock cycles after the
level is exceeded at the input and, therefore, provides a fast indi-
cation of the input signal level. The coarse upper threshold levels
are listed in Table 21. This indicator remains asserted for a
minimum of two ADC clock cycles or until the signal drops
below the threshold level.
Table 21. Coarse Upper Threshold Levels
Coarse Upper Threshold
Register 0x105[2:0]
C_UT Is Active When Signal
Magnitude Below FS
Is Greater Than (dB)
000
<24
001
24
010
14.5
011
10
100
7
101
5
110
3.25
111
1.8
Fine Upper Threshold (F_UT)
The fine upper threshold indicator is asserted if the input
magnitude exceeds the value programmed in the fine upper
threshold register located in Register 0x106 and Register 0x107.
The 13-bit threshold register is compared with the signal magni-
tude at the output of the ADC. This comparison is subject to the
ADC clock latency but is accurate in terms of the converter
resolution. The fine upper threshold magnitude is defined by
the following equation:
dBFS = 20 log(Threshold Magnitude/213)
Fine Lower Threshold (F_LT)
The fine lower threshold indicator is asserted if the input
magnitude is less than the value programmed in the fine lower
threshold register located at Register 0x108 and Register 0x109.
The fine lower threshold register is a 13-bit register that is
compared with the signal magnitude at the output of the ADC.
This comparison is subject to ADC clock latency but is accurate
in terms of the converter resolution. The fine lower threshold
magnitude is defined by the following equation:
dBFS = 20 log(Threshold Magnitude/213)
The operation of the fine upper threshold indicators and fine
lower threshold indicators is shown in Figure 67.
Increment Gain (IG) and Decrement Gain (DG)
The increment gain and decrement gain indicators are intended
to be used together to provide information to enable external
gain control. The decrement gain indicator works in conjunction
with the coarse upper threshold bits, asserting when the input
magnitude is greater than the 3-bit value in the coarse upper
threshold register (Address 0x105). The increment gain indicator,
相關PDF資料
PDF描述
RCC15DRAN CONN EDGECARD 30POS R/A .100 SLD
IL13-EU1-H05-3100-200 LOCKING LINE CORD 3 COND EU 2M
AD9640-125EBZ ADC 14BIT 125MSPS DUAL 64-LFCSP
RCC15DRAH CONN EDGECARD 30POS R/A .100 SLD
AD9640-105EBZ ADC 14BIT 105MSPS DUAL 64-LFCSP
相關代理商/技術參數
參數描述
AD9640ABCPZ-105 功能描述:IC ADC 14BIT 105MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 位數:12 采樣率（每秒）:1.8M 數據接口:并聯 轉換器數目:1 功率耗散（最大）:1.82W 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:管件 輸入數目和類型:2 個單端，單極
AD9640ABCPZ-125 功能描述:IC ADC 14BIT 125MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 位數:12 采樣率（每秒）:1.8M 數據接口:并聯 轉換器數目:1 功率耗散（最大）:1.82W 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:管件 輸入數目和類型:2 個單端，單極
AD9640ABCPZ-150 功能描述:模數轉換器 - ADC 14Bit 150Msps Dual 1.8V PB Free ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體:
AD9640ABCPZ-80 功能描述:IC ADC 14BIT 80MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD9640ABCPZRL7-105 功能描述:模數轉換器 - ADC 14Bit 105Msps Dual 1.8V PB Free ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*